start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Thanks! I can reproduce it in this way now! Ill apologize, i had a slightly differnt way to set things, and then its ok. Stand by, well check whats going on there. 625 is definitly not correct.by ulrich - Café
I dont know about how the manufacturers interpret the "0" Position, in our implementation its half of the 1500 definition. So it may be better written as 750, but thats still inside a 1.2% Tolerance. All zeroed i measure 754uS, two clicks in the trim gives 762US. So thats super close, not exactly "way off". Can be fixed by a single click of trim, which is needed anyways. Unby ulrich - Café
Ok, schau ich mir an. Danke für die Info! Eigentlich sollte bei +-120 Schluss ein.... OK, gefunden: Es ist ein Anzeigefehler. Der negative Wert wird als 256-x angezeigt. Wird beim nächsten Update behoben. Der Trimmwert ist aber trotzdem korrekt, wird nur falsch angezeigt.by ulrich - Café
It seems it needs more explanations. What is been seen here is an problem that arises if the frequency is choosen too high. On the Swashplate the higer frequencys do not work for all Setups, thats the reason we choose 144Hz back in the days, since this fits best for almost all helis. More in not always better, there is a sweet spot. When upping the drive rate, the maximal transferred frequencyby ulrich - VBar VLink
Its a known issue. It will be adressed with the next update soon.by ulrich - Questions VBar Control Touch
Gibts denn ein Thema was Euch interessiert? Ich hätte da 2 Vorschläge: 1) Frameraten, Pulsbreiten, Latenzen was bringts. 2) Antennen für 2.4Ghz etwas genauer beleuchtetby ulrich - Café
Yes, you are right, and Rainer dosent know that is actually should work. Unfortunately it has some problems we found during trying it out. So we will look into it and make it work. To enable the PC Connection, the Cable has to be attached *after* the Unit is powered up, otherwise it will end up in the bootloader.by ulrich - VBar VLink
Yes, these updates fixed a small issue with the nitro governor status display. No other changes.by ulrich - VBar VLink
Zu 1. Hast Du genau richtig gedeutet. Das kann in extrem echohaltigen und kleinen Räumen passieren. Da wird geprüft, ob zwischen den eigentlichen Signalen eine ausreichende "Stille" herrscht. Das mit dem Läufer ist eine perfekte Lösung! Zu 2. Wenn der Heli auf der Plattform steht ist das Signal nicht optimal, einfach weil der Winkel zwischen Sender und Empfänger ungünstig ist.by ulrich - Logo 200/400/500/600 Fragen
Genau so soll es sein. Ich hatte das Update vor meinem Post gemacht.by ulrich - Café
So ne Kleinigkeit hat sich als ganz schön harte Nuss herausgestellt. Die neue CPU kann den Pin Status nicht mehr wie früher einfach ansynchron abfragen. Ich werd versuchen das mal beim Chiphersteller abzuklären. In der Zwischenzeit zeige ich einfach den Wechsel des Signals im Status an (fallende Flanke = Wechsel von high auf low am Pin). Man muss mit der aktualisierten Version also den Magnby ulrich - Café
Ich weiss. Wird ja auch so werden, nur grad ists leider nicht so.by ulrich - Café
Sicher das er nicht geht? Oder nur die Anzeige nicht? Ich sehe gerade, das die Anzeige im Sender nicht korrekt funktioniert (nur das "RPM Signal" Feld), das Signal aber trotzdem richtig ausgewertet wird.by ulrich - Café
Ich denk ich weiss was es ist. Bitte update mal die EVO, ich denke dann wird sie genauso gehen wie die NEO mit diesem Sensor. Falls nicht, müssen wir weiter forschen...by ulrich - Café
Default ist beim Regler bei der NEO 14ms = 70Hz. Mit dieser Einstellung wird man genau gleich sein wie bisher.by ulrich - Café
Wenn Du zwei 10k Widerstände nimmst, und diese parallel zum Schalter schaltest, geht ein 3 Wege Schalter. Wenn Du nur 2 Wege brauchst, geht auch einfach nur 1:1 ein Schalter.by ulrich - Café
Its 2.4Ghz "only". I hope there will be dual band versions of the wifi module in the future. But its still way better than the touch´s one.by ulrich - VTV
Vbar NEO already has static protection on all connections. The EVO has an improved static protection on the antennas. However, static protection is often not enough to protect against direct hits of sparcs from belts etc, which tend to exceed all possible protecion measures.by ulrich - VTV
"Potless" Knüppel, also die mit der magnetischen Abtastung sind zwar etwas günstiger, bringen aber keinen erkennbaren Vorteil. Die Kalibrierungen und Umrechnungen, die man machen muss um auf dieselbe Linearität zu kommen verschlechtern die Genauigkeit doch ganz schön. Wir haben inzwischen sehr viel Erfahrungen mit unseren Aggregaten, und können sagen das der Verschleiss der Potisby ulrich - VTV
The License Policy is not changed at all. Licenses are bound to the device, they may be sold with the device, but removing licenses from devices is not possible apart from exceptions in case of service actions.by ulrich - VTV
Wir werden wieder deutsch/englisch gemischt reden. Eine bessere Lösung ist uns dazu noch nicht eingefallen.by ulrich - VTV
We have, but we dont stop thereby ulrich - Café
Please use this Thread for your Questions to EVO Fragen zur Sendung über EVO bitte hier hinein.by ulrich - VTV
There shall be a clear gap between multiple units. As long as your own heli is siginificantly nearer than another one it shall be fine. Howeer we do not recommend operating mutliple devices near each other. Even if not finally confirmed 10m distance between the maximum ranges shall be ok. So the Bases shall be 30m apart if maximum range is used.by ulrich - Fragen zum Flight Trainer
Hmm, ist auf jeden Fall eine interessante Idee für ne App.by ulrich - VBar VLink
No ist not. Unfortunately since some time there is a shortage of chips wich gives us trouble keeping up with demand. As soon as this clears up, we will catch up.by ulrich - VPlane/VBasic VLink
Ich konnte das nachvollziehen, da ist beim letzten Update irgendwas schiefgegangen. Ich hab die Firmware mal nochmal aktualisiert, jetzt müsste es wie gewohnt gehen.by ulrich - VCopter VLink