start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Thanks for sharing Rainer, this looks like a fun project to do. Peterby Vinger - Videos/Pics
Hi Rainer Is this from a kit or where did you get the scale fuselage? Really nice little toy. Peterby Vinger - Videos/Pics
Thanks Rainer it seems that he got it figured out.by Vinger - VPlane/VBasic VLink
Thanks for the reply. In your pic of macrocell 11E1CH1 is what we use, but if you select input signal as Channel 1 then the wing mixers work but not the gyros. If we select input as FC Elevator then the gyro works but the wing mixer settings not. This is from the guy I am helping as I do not have a test rig with SBus unit to verify. Cheers Peterby Vinger - VPlane/VBasic VLink
Hi Rainer Thanks for the info. I am still a little confused about what to use when on each flight control output. What we have is that if everything is left at default with only SBus selected as output from the Neo, then there are no gyro stabilization and the wingmixers have no effect on the channels. So if one choose say FC-ELEVATOR as input at the macrocell channel for say the elevatorby Vinger - VPlane/VBasic VLink
Hi RV Vplane with Sbus output from Neo into a power distribution box. Am I correct in assuming that at the flight controls channel's macrocells one has to select FC-xxxx as input for the gyro function to work? Setting maximum throw is that still done in the wingmixer setup? Will all the AGILITY and GYRO settings in flight settings still be active for BANK switching as per normal VPlaby Vinger - VPlane/VBasic VLink
Hi Rainer What will happen to the setting if I adjust it via VBCt to say a value of 130 and the owner goes back to using the PC software as he or she uses another radio system? Peterby Vinger - Café
Hi RV Thanks but when and how will one use this?by Vinger - VPlane/VBasic VLink
I am busy setting up a Neo with an EXTENDER and when I did the IO Config came across this screen as in attached picture. What does it do and how does it work? Regardsby Vinger - VPlane/VBasic VLink
I do not have a standard Neo (non Vlink) and VSat to test, but the question is can VPlane be loaded on this combination? Regards Peterby Vinger - VPlane/VBasic VLink
The forum only accepts ZIP files and not RAR files. So you need to compress the files to ZIP archives.by Vinger - VPlane/VBasic VLink
Connect the USB cable, set VBCt to USB drive in TX settings and use Explorer in Windows to navigate to the VBC which will be shown as a drive.by Vinger - VPlane/VBasic VLink
Save the setup file to your VBC/VBCt, and save the Macrocell setup to your VBC/VBCt, naming them to the model name for easy recognition. Connect to PC and copy both these files to your PC and zip them and attach to the forum thread.by Vinger - VPlane/VBasic VLink
Back to this setup. A strange occurrence happening. Even with gain dialed to zero in Bank 2 and 3 the elevator and ailerons still give stability and this is way to much for the flight conditions of this jet. Another effect is that EXPO has no effect as well. Battling to understand this as I have never run into this. Regardsby Vinger - VPlane/VBasic VLink
For any turbine as they all have similar start procedures.by Vinger - Setups
That would be helpful thanks Eddie.by Vinger - VPlane/VBasic VLink
Hi Rainer gave me this answer in attached file here on the forum. It is actually very simple and only makes use of the MOTOR switch.by Vinger - Setups
Hi Rainer AUX 3 as input to a MC is not available when connected to an Extender, so cannot use that. Care to explain how to do this as input say to MC 14 in the setup above? Thanks again. Peterby Vinger - VPlane/VBasic VLink
BUT - start with a curve or channel with defaults there and set the inputs to the "original MC's" (internally passed through then ;-) ) as they are CH4(On CH4 Socket) and AUX3(On the Slave Flaps socket) and NOT CH9. Hi Rainer Can you explain this bit as there are no AUX 3 socket available on both Master and Slave?by Vinger - VPlane/VBasic VLink
Thanks Rainer It makes sense to use it that way, my brain just got confused. The value for the flaps mix in wing mixer was zero in the attached files but I did try that, but will change the setup to what you recommend. Thanks againby Vinger - VPlane/VBasic VLink
Hi Helping a friend with his VPlane setup with extender. Have a few questions, files attached. 1. Are the flap system as I have set it correct? It works perfectly. 2. Cannot get the elevator mix to flaps to reverse, values are only positive. 3. There are no MANAGE BANKS menu to get to copy banks. Don't know if this is since the latest update or not? Thanks for checking.by Vinger - VPlane/VBasic VLink
You need to download and install a new script file to access it via the PC software. https://www.vstabi.info/en/node/2345 Feature explained here https://uroehr.de/vtube/video/anti-gravity-explained-with-kyle-dahlby Vinger - VBar NEO (non VLink)
Lightness is set. Just dial that to ZERO.by Vinger - VBar NEO (non VLink)
Fingolf Wrote: ------------------------------------------------------- > 3. There is a new app for the screen lock. > > Stephan I know that but many user out there does not, apps does not automatically gets announced that an update is available VBCt only announces it’s own update. So user update the radio but not the apps.by Vinger - VTV
kreids Wrote: ------------------------------------------------------- > ulrich Wrote: > -------------------------------------------------- > ----- > > We understand this of course. Its very hard to > > find good solutions with the languages. Our > > userbase is probably most english speaking, but > in > > the past we had by far the most viewers on ourby Vinger - VTV
Questions 1. There so many errors with WiFi update that gets fixed by redoing it via USB, why do you insists on Wifi update as primary update process. 2. What causes the file system to get corrupted, why can this not be checked by the VBCt itself? 3. Two finger lock and helicopter pictures on home screen disappearing and cannot be re-enabled seems to be the main complaint after Darkby Vinger - VTV
Did you disable the Kontronik BEC by removing the red wire in the throttle lead?by Vinger - VBar NEO (non VLink)