start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Hi Guys, Any idea what the ESC Output Type should be set when paired with a Hobbywing 120a ESC? I can't seem to find any information on such. With regard to tail setup. Should the tail servo (Futaba BLS276 SV) be first powered up to locate its neutral point to find best servo arm fitment for 90 degrees. Then power off and adjust the servo arm by hand for 90 degree linkage setup? Once complvon Razmo - Questions VBar Control Touch
Hi Eddie, Appreciate it. I'll be back to you in a few weeks. Imminent travel, etc. Razvon Razmo - Questions VBar Control Touch
Appreciate it GruB. I'll throw a couple comparison videos together as I have a handful of friends with EVO's. I'll try a general volume of 60% for now, but I fly at a noisy field and louder alerts can be needed without distortion. It seems some may have either faulty programing or faulty speakers as I'm rather sure my original comparison proved mine sounded faulty with identical settings. Myvon Razmo - Questions VBar Control Touch
Hi Eddi, The EVO I compared mine with was a from recent purchase, September or October of last year. Mine is from the first shipment that made it to the states. I could likely procure the serial number from my friend if you think that might help. In way of speaker replacement, if the actual speaker itself is the problem. What would be needed on my part to replace the speaker myself?von Razmo - Questions VBar Control Touch
Hi Eddi, Well, I suppose my disappointment stems from comparing the sound output from a friends EVO to mine. Their speaker did not emit the distorted sound mine does at the same settings. Their sound remained clear. Do you mean, although I have a problem with my transmitter, it can be alleviated with adjustment but not extirpated without repair? What would the Home Zone App provide? It emitvon Razmo - Questions VBar Control Touch
Hi Eddi, Thought I'd send a video for reference. Please let me know.. https://youtu.be/Cltyntgpkwg Thanks, Razvon Razmo - Questions VBar Control Touch
Hi Eddie, Appreciate this. Do you mean you'll be able to make programing changes remotely after I submit a service ticket? Also, if necessary. I'm plenty comfortable opening the transmitter if needed. Even replacing the speaker if it isn't too complicated. With regard to the speaker, below 80% it sounds somewhat normal, but still a crackles some. Greater than 80% and it sounds terriblevon Razmo - Questions VBar Control Touch
Rainer, AR position of motor switch? What does AR stand for? It would be nice to have sound options of course. I'm in the states, file a return where? Can the speaker not be replaced easily? Razvon Razmo - Questions VBar Control Touch
Thank You. A couple questions.. 1) What is the difference between AR/Off Only and Always On? 2) Can I change the sound of the beep? My VControl EVO speaker has never emitted a clear sound at high volume. I'm thinking my unit was shipped with a faulty speaker. My friends VControl, emits a much clearer sound than mine for whatever reason. Razvon Razmo - Questions VBar Control Touch
Hey Rainer, Is this somehow only activated per Vbar? I have the "PitchClick" App active in my VControl. Razvon Razmo - Questions VBar Control Touch
Hey Guys, How do I activate the center collective beep function? Thanks, Razvon Razmo - Questions VBar Control Touch
Hi Eddi, Thank you for the explanation. Very helpful. Razvon Razmo - Questions VBar Control Touch
Hi Guys, I picked up a set of the AG01-V Gimbals. I've heard some users having already installed and using the gimbals without error have now experienced a system lock (unable to use their VControl) after the latest software update. What's strange to me, it doesn't seem to be affecting every user. Is this correct? Curious what your thoughts are here. I was looking forward to installing them.von Razmo - Questions VBar Control Touch
Thanks Rainer, Quick question, before I set things up. I did try reversing the presigns for output min/max (end-points). For example, I changed the default -100/+100 to +100/-100. After doing so, the servo goes dead. Meaning, when I apply stick input the servo does nothing after the change. Why is this? Thanks, Nickvon Razmo - VPlane/VBasic VLink
Hey Rainer, I setup maximum throw (45up/45down) in setup. It seems I'll never be able to accurately measure for a low or mid rate on the bench or ever as adjustment can only be done per flight mode with an active control loop. Is that what you're telling me? With regard to Elevator Mix. My servo arm was moving in the wrong direction so I activated reverse in Elevator setup. Could this posevon Razmo - VPlane/VBasic VLink
Hello, I'm new to Vplane, but I'm not new to fixed wing control rate setup. From experience, I've always setup my fixed wing models by maximizing control resolution using proper control rod geometry and end-points as a first step to produce maximum control angle for high rate throws. I've also noticed maximum end-point travel is 120/120 in vPlane. As an example, I was able to achieve maxivon Razmo - VPlane/VBasic VLink
Appreciate it Eddi, Razvon Razmo - Questions VBar Control Touch
Hello, If I accidentally activate my Vplane auto trim switch at the bench or while ground taxing. Should I then open up the auto-trim menu to check that all axis are at zero before flight? If each axis isn't at zero, I assume I can simply reset each axis to zero manually prior to take off, correct? Thank You, Razvon Razmo - Questions VBar Control Touch
Thanks Rainer. It would be great to see an updated manual for the VBC Evo. Where can I find information on your RFID Reader and Tags? Thanks, Razvon Razmo - Questions VBar Control Touch
Hello, Although I've read the help menu in the radio, which says to enter context menu with a long-click on a battery. Does this mean a long press on the battery I want to delete in my list of added batteries? I've tried this and nothing pops up to provide me with an option to delete battery? I've also tried a long press on edit battery but nothing happens. I am running pro, but I believe I avon Razmo - Questions VBar Control Touch
Hi Peter, Out of curiosity, before changing any other values, had you first tried adjusting the throttle to gain reduction setting? Or possible a better question. What is your friends throttle to gain reduction setting on his other aircraft? With my VBCT Evo, I'm noticing the gain reduction setting is defaulted to 0. However, I'm trying figure out why my VBCT Evo only seems to allow such avon Razmo - VPlane/VBasic VLink
I hadn't realized the default was set to 70% capacity, which now I understand I can fly until 0% which is roughly 30% remaining. After flying to 0% I now get a vibration alert which works great. I may just prefer turning the % alerts off since she'll vibrate at 0%. Thanks, Razvon Razmo - Logo 200/400/500/600 Questions
Is there a way to configure the telemetry sensor to only announce a 20% alert along with vibration? I'm getting an alert every 10% which I don't need making it easy to miss the 20% alert and I'm not receiving a vibration? Razvon Razmo - Logo 200/400/500/600 Questions
Eddi, I'm a little confused. Do you mean I can play with Anti Gravity so the 200 hovers upright say around 60% stick input and hovers inverted around say 40% stick input? Is Anti Gravity alteration a feature Pro only? Yes, I'm familiar with the lack of collective control on the M2. Thanks, Nickvon Razmo - Logo 200/400/500/600 Questions
Still new to using the Vcontrol Evo and Logo 200, but noticing default setup isn't 0 pitch at 50% stick input which produces an awkward hovering inverted stick position for my taste. Why cannot I not find collective travel and a pitch curve setting in the Logo 200 menu? Keep in mind this is my first Vcontrol and Logo 200. Thanks, Razvon Razmo - Logo 200/400/500/600 Questions
Appreciate it Eddi, thank you.von Razmo - Logo 200/400/500/600 Questions
Hi Eddie, I'm just back from flying her for the first time. Totally agree. Absolutely no need to add weight. She's flies great! By the way, I'm new to the VControl Evo. I see that the radio provides a graphical view of remaining capacity, but how to do I activate remaining capacity voice alerts? Or at least one audible & vibration alert once I reach my preferred remaining capacity limivon Razmo - Logo 200/400/500/600 Questions
Hi Rainer, Interesting. I had not thought adding weight to the tail could influence it's control behavior. Did you prefer to leave it nose heavy or add a bit a weight to the frame? Thanks, Razvon Razmo - Logo 200/400/500/600 Questions
Hi Guys, Ordered the Logo 200 with U/I Sensor. I have not yet flown her, but noticing she's very nose heavy with the stock 650mah LiPo as far back as possible and U/I Sensor installed. Should I be adding a bit of weight at the tail for proper center of gravity? Thanks, Razvon Razmo - Logo 200/400/500/600 Questions