start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Hello Guys, I have just installed a VBar Control (updated) and NEO PRO+RESCUE (also updated) on my Logo, but cannot find the screens that are shown here: http://www.vstabi.info/en/node/1930 Am I missing something? There's a mention of a smiley face but I do not see that in my VBar Control and have also looked everywhere inside it for Rescue and did not find it... Can you please helpby Flipper 76 - Questions VBar Control
Thanks Eddi! so the Batt ID should recognize the RFFID sticker to the side of it and not on top of it? Because I tried putting it on one of the batteries but because the Batt ID is inthe middle of both batteries and the RFID sticker is to the side stuck in one battery, it would not be close enough to be recognized by the Batt ID... could I be doing something wrong here? Only when I put theby Flipper 76 - Logo XXtreme 700/800 Questions
Thanks Eddi, but my question is that on the pictures your sticker on the 12S packs is not in one single battery, it is in between the 2 batteries, so what happens to that sticker when you dissassemble the 12S pair? You have to remove it and then put it back on when you use it as a 12S pack again? I saw that you secured the sticker with clear tape on the pictures... Cheers, Flipperby Flipper 76 - Logo XXtreme 700/800 Questions
Thanks RV, but how did you fix the RFID to the 12S packs? in the middle of the 2 batteries like Eddie did? and you have to install and remove the clear tape to hold the RFID in place on every flight? I appreciate your input here...by Flipper 76 - Logo XXtreme 700/800 Questions
this is the other link I referred to on the message above: http://www.vstabi.info/de/node/1740 Cheers, Flipperby Flipper 76 - Logo XXtreme 700/800 Questions
Hello Everyone, I built my Logo 700 and positioned the Batt ID according to this link, on Eddi's 800: http://www.vstabi.info/en/node/1968 Since I'm also using the same batteries on my Logo 550SX (also with Batt ID), I want to follow the instructions you have given on how to do that, basically using one RFID for each 6S Batt and another RFID for each 12S pair. I could not find that link,by Flipper 76 - Logo XXtreme 700/800 Questions
Thanks very much RV and Eddi, we're thinking about replacing the shunt, we ordered a few different ones from Vishay and will try to do some tests, it will take a while but we'll report if any experiment is succesful... Best Regards, Flipperby Flipper 76 - Questions VBar Control
Hello RV, thanks for your answer, the slave cable from the Kosmik BEC is connected to the Aileron port in the Silverline Vbar, would the orange cable being connected there be a potential problem? Thanks for your help here, Flipperby Flipper 76 - Questions VBar Control
Hello Rainier, we realized on Eduardo's heli above, that the slave wire from the Kosmik BEC did not have the orange wire disconnected and grounded as I saw Uli recommend in a different post. Do you think that trying to disconnect the orange wire from the slave cable might solve this issue? Thanks for giving us your point of view here, your help is much appreciated! Cheers, Flipperby Flipper 76 - Questions VBar Control
great news, worth the wait for meby Flipper 76 - Logo 200/400/500/600 Questions
Hello, I need a 600SX 12T pinion, item 04636, has it been discontinued? I need that pinion for my motor to work optimally, what should I do??? Thanks and hope that you are producing a new batch...by Flipper 76 - Logo 200/400/500/600 Questions
hahaha! ring packs below the main gear would be a novel idea!by Flipper 76 - Logo XXtreme 700/800 Questions
Hello Uli and RV, I heard from people at IRCHA that the battery configuration on the new plastic logo 700 will change from saddle to stick pack, is this true? Sorry, I know it's still under development and it's a log ways off, but just very curious...by Flipper 76 - Logo XXtreme 700/800 Questions
Hello Everyone, I'm wondering where should I install the Pro Rescue on my V Control, is the intention to be able to flick instantly kind of like a throttle hold, in an emergency? What switch are you running it on? I pinch the sticks, no thumbs, so I don't have fingers below by the lower longer switches, I'm running my security switch on the left side, but I don't need to access that while fby Flipper 76 - Questions VBar Control
Hallo zusammen, what do you recommend the 90A dampeners for? Above a certain RPM, or harder smack style? What are pros and cons? I'm going to be between 2,000 and 2,150 rpm, are the stock ones still good here? Are the harder dampeners not recommended below a certain RPM? Thanks guys, I know a lot of this is personal preference, but I wanted to understand if there are any limitationby Flipper 76 - Logo XXtreme 700/800 Questions
Hello Rainier and Uli, waht is your opinion regarding Eduardo's suggestion? Thanks for looking into this! Cheers, Felipeby Flipper 76 - Questions VBar Control
Hello, I'm building my first (definetely not the last ) Logo 700, and in the manual it says to put loctite on the bolt that hold the main blade to the blade grip? Would that not be necessary since there's a nylon locking nut below? Also, is it safer to use red loctite on all the bolts in the main rotor head instead of blue loctite? Spindle and the ones below? Thanks!by Flipper 76 - Logo XXtreme 700/800 Questions
what's the recommendation for interface to be used with AccuRC? Is it confirmed you will release a v2 sim interface based on the Neo? Thanks!by Flipper 76 - Questions VBar Control
please excuse my ignorance, but what are these for and what's the recommended application? I understand they limit your stick travel on the collective, but what does that do and/or what is it for? Thanks!by Flipper 76 - Questions VBar Control
which switch on vcontrol are you running rescue on?by Flipper 76 - Logo 200/400/500/600 Questions
Hello Guys, what is the ideal size of tail blades to be used on the 700 Exxtreme? 105 or 115? Thanks!by Flipper 76 - Logo XXtreme 700/800 Questions
Hello Eddi, RV und Ulrich, I was wondering what are the recommended settings by Mikado for use of the Vbar Control and VBar Governor and YGE settings on the drive set for the Logo 550SX: YGE 120LVK and Kontronik Pyro 650-103L. 1- What is the recommended gear to be used, what throttle opening should I target at my intended rotor RPM: 80, 85 or 90%? Does that depend on the Vbar gov or the ESCby Flipper 76 - Logo 200/400/500/600 Questions
Hello, I noticed that in your building tips for the 550SE and VBar NEO you soldered the U/I Sensor the the ESC cable, is that correct? http://www.vstabi.info/en/node/1970 Can you please provide us with directions on the best way to do so without damaging the sensor? Thanks and best regards, Felipeby Flipper 76 - Café
Hallo, was ist das kW Grenze des YGE 90LV ? Wie wärs mit einem Pyro 650-103L auf einem 550SX ? danke, Felipeby Flipper 76 - Logo 200/400/500/600 Questions
Hello Sir, the pinion shim on the 550SX is 5x10x1, and it seems to be putting an axial load on my counterbearing supporting the tip of the motor shaft. I've already checked and there's no room to bring the pinion up, or I'd have to remove shims from the main shaft to try to bring the whole main gear up so it would not be misaligned with the pinion at the apex of the herringbone. My questionby Flipper 76 - Logo 200/400/500/600 Questions
Hello Eddi, sorry it took so long for me to get back to you, I only saw your reply recently. Please find the pictures attached, you can see on the second photo the remainder of the melt balls... it got really hot! I will try an RMA with Mikado USA which is easier for me, thanks a lot for your help!by Flipper 76 - Logo 200/400/500/600 Questions
Hello Jorg, what is the maximum HS you can run with the stock combo, 15t pinion, vbar governor? I'm using YGE90LV, Scorpion 4025-110kv, vbar gov and vbar control. What does not overheat the motor? I'm asking becasue I don't know if I got a faulty Scorpion but it heated up too much and melted the bearings... Thanks!by Flipper 76 - Logo 200/400/500/600 Questions