start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Hi, i installed a Vbar rx 7ch on a plane where i found the offset parameter to be setted as needed. This value has to do with the torque that the aircraft can generate when giving motor input or what is this parameter for? Regardsvon Marianovbar - VBar VLink
Hi, i installed a Vbar rx 7ch on a plane where i found the offset parameter to be setted as needed. This value has to do with the torque that the aircraft can generate when giving motor input or what is this parameter for? Regardsvon Marianovbar - VPlane/VBasic VLink
Hi guys, thanks to both for the explanation, i will set up again with the 14 tooth pinion. Regards!von Marianovbar - Logo 700/800 Questions
But.. 535kv x 44,4v / 10,46 = 2270 rpm and in the graphic with 100% pwm at the end of the flight i have like 2096 So why less? Regardsvon Marianovbar - Logo 700/800 Questions
Hi, i tested 13 tooth pinion and i was able to increase my tail gain like 20 points without any overspeeding and now is more stiff, also the motor has more torque. But i'm having a pwm too high now so after mid flight heli start to loose some rpm in some maneuvers and feels like less power as it gets close to the end of the flight. Some advice to lower pwm scores? Bigger blades and less rpm?von Marianovbar - Logo 700/800 Questions
Hi eddie, i didn't show in the video but if i do fast tail reversals or big pitch inputs the motor, not the rotor, sounds like overspeeding or overgeared, that is why i had to lower my gains from gov and the tail to 35 or less, and still doing it in some agressive maneuvers.. i broke 2 belts because of that.. This is why i mentioned to change from 14 tooth to 13, to fix the "overspeeding&von Marianovbar - Logo 700/800 Questions
Hello guys. My thrust bearings and dumpers from the tail are new ones, also the bearings of blade holders. My tail gain is very low, like 35 because if i increase it, i have gear chatter from the motor and also to avoid that i had to decrease the P gain from gov. Maybe 13 tooth pinion works better for Hk5 535kv motor? So in that way i don't have gear chatter and increase my gain to don't break gevon Marianovbar - Logo 700/800 Questions
Hi, i'm having issues with a slow tail wag on climbouts. I already decrease/increase coll. precomp and nothing happens... using scorpion gov and vbar gov same issue, i left it on scorpion gov. Kst x1035 tail servo, 500hz frequency and Vbar EVO. The tail mechanics are not hard when i move. https://youtu.be/Rn9snnfDZAw Regardsvon Marianovbar - Logo 700/800 Questions
Great, i didn't know about the oscilloscope feature.. Thank u very much. Regards Mariano Suárezvon Marianovbar - VBar VLink
Hi, just a concern, it might be a useful put a servo test feature on vbar control? Is there any different better process than doing it manually? or putting pitch pump parameter close to 100? Regards. Mariano Suárezvon Marianovbar - VBar VLink
Hi Eddie, okay. Now i'm not understanding for which case should be used "no aging" option if any battery ages after a few cycles... I saw Kyle stacy video where he explained that this option he used is for new batteries what makes sense for me but idk till which point. Anyway, i will measure how much capacity my batteries takes from the charger and flight to compare if is similar and rvon Marianovbar - VBar VLink
Hi, is possible to fix in some way the swashplate play after long use? Or just change it? There is info about when will be in stock again? Regardsvon Marianovbar - Logo 700/800 Questions
Oh okay because i started with no aging and using 75% capacity, after almost 50 flights now at the end of the flight i noticed rpm dying a little bit. Regardsvon Marianovbar - VBar VLink
Hi, with new packs of batteries i set no aging, after a hundred flights i have to change the aging to low or medium so the vbar recalculates battery capacity? Or just leave it in "no aging" for new batteries? Regardsvon Marianovbar - VBar VLink
Hi, i want to replace the vcontrol knobs with or without his base. I need to open the back of the radio or just removing from the front is possible? Regardsvon Marianovbar - Questions VBar Control Touch
Hi, what ESC framerate exactly does? i have it on 72hz and i read on vstabi that if u don't use Vgov is not necessary touch the value but idk if that depends also on ESC or servos. I have a Logo 700, Tribunus II 200A and Kst x2208 333hz and x1035 500hz I'm havin a tail kick even after lower my P I gains from scorpion gov but still there. Regardsvon Marianovbar - VBar VLink
Hi, short one. Which port is for connect the satellite on the silverline? Regardsvon Marianovbar - VBar VLink
Yes, he has that app and already uninstalled, at the moment no issues. i will ask to my friend to do that check. Thank u, regards!von Marianovbar - Questions VBar Control Touch
I'm talking about the screen that comes after links a model, the one is showing some inputs and macrocells and after that the black screen. the vertical lines are normal for me Regardsvon Marianovbar - Questions VBar Control Touch
Hi, a VBC-T from a friend does randomly what is show in the photos attached after links with a model. He already updated through USB 3 weeks ago. Regards.von Marianovbar - Questions VBar Control Touch
Hi, i read that a NEO non vlink license can be transferred to a NEO vlink But a NEO v1 license with rescue can be transferred to a NEO vlink? Regardsvon Marianovbar - VBar NEO (non VLink)
I bought it last week to MikadoUSA so should not be a V1 i suppose... I will look at the devices list when i register this device. Regardsvon Marianovbar - VBar NEO (non VLink)
Hi, I want to know if Vbar NEO 6.x express (without antennas) can work as Vlink if i put the antennas inside, instead of a vbar satellite. Regardsvon Marianovbar - VBar NEO (non VLink)
Hi. Is possible buddybox between vcontrol touch and vcontrol touch evo? Regardsvon Marianovbar - Questions VBar Control Touch
Hi, vbar neo is compatible with Spektrum SRXL2 DSMX Remote Receiver? https://www.horizonhobby.com/product/srxl2-dsmx-remote-receiver/SPM9747.html Regardsvon Marianovbar - VBar VLink
Hi. General tweaking order steps are the proper way to set up the vbar governor? or also is okay if i just dial in the rpm until matches in the screen and then dial the other parameters individually? Regardsvon Marianovbar - VBar VLink
Hi. Will there be an update of the neo mini in the future to have the shiver filter and tail torque extend parameters? Regardsvon Marianovbar - VBar VLink
Hi. I attach a logfile of one of my NEOs. Is possible to check if there is nothing weird? I had 2 crashes with that one where the heli did what it wanted a few seconds after take off with the bank 3 loaded. The ESC is working okay in another heli, motor, batteries. The only thing left is the neo, servos and wiring Regardsvon Marianovbar - VBar VLink
Hi Eddi. understood. And if the vbar neo is solded needs to be transfered to the new user or that is just with the old vbars? Regardsvon Marianovbar - VBar VLink
Hi. Is it possible to transfer the license from my Vbar Neo to an new Vbar Evo? Regardsvon Marianovbar - VBar VLink