Alle Beiträge dieses Benutzers

Re: VTV 15 - Advent, V8 and much more - 9 Tagen

Will the VBCt support V8.2 Thanks Peter

Re: VTV 15 - Advent, V8 and much more - 9 Tagen

Hi All Thanks for the effort of making the video. Will 8.2 fix the elevator "bobble" or the up and down oscillation of the tail boom that many customers have experienced? Thanks Peter Rossouw

Re: Head Wobble Logo 600SE - 4 Wochen

Here is the video explaining the sanding of the dampers https://uroehr.de/vtube/cat/technical-support/video/low-rpm-dampener Regards Peter

Re: New Sab 700's with tail bob and shake issue on V8 - 6 Wochen

tc1975 Wrote: ------------------------------------------------------- > > So why do you run 12V Servos at 8,2V??? Because the BEC does not support 12V and the servos perform perfectly at the lower voltage.

Re: V8 im TDSF - 2 Monaten

I have tested Evo with V8 in my TDSF and it works perfectly. I first flew the TDSF with V7 and once dialled it upgraded to V8. You would still need to adjust main gain, control response and stop support to get the ultralight blades and zero damping head to fly without any wobbles. Peter

Re: Tribunus III telemetry issue - 3 Monaten

Hi Do you have the telemetry cable correctly plugged in, PC Port on ESC to Teleport on the Neo?

Re: Wechsel von VBar Neo auf EVO, welche Version - 4 Monaten

Hi Thomas I have extensively tested my TDF with the recommended MKS servos on V8. The TDF was my testbed for beta testing of V8 on an Evo. I use 1400-1500 and 1600 rpm in the three banks. You can set the servo update rate to 333Hz with no negative effect. I use 12S packs and Scorpion ESC/Motor combo. Peter

Re: New Sab 700's with tail bob and shake issue on V8 - 4 Monaten

tc1975 Wrote: ------------------------------------------------------- > Vinger schrieb: > -------------------------------------------------- > ----- > > tc1975 Wrote: > > > -------------------------------------------------- > > > ----- > > > Would be great to get an advice for the 12V > KK > > set > > > - swash and tail.

Re: New Sab 700's with tail bob and shake issue on V8 - 4 Monaten

tc1975 Wrote: ------------------------------------------------------- > Would be great to get an advice for the 12V KK set > - swash and tail. As per my previous post the Kenny Ko V2 12V Theta servos work perfectly on my Henseleit helicopters with zero bobble issues with the stock servo settings. Cyclic servos D is 53 and tail servo D is 128 Peter

Re: New Sab 700's with tail bob and shake issue on V8 - 4 Monaten

sanjeev joshi Wrote: ------------------------------------------------------- > Another thing I want to point out. A lot more > people are now coming out recognizing the issue > now they know what to look for based on symptoms. > I actually see a lot more issues on the online > forums but I am not jumping into every thread. > The symptoms are there. Not sure why more

Re: New Sab 700's with tail bob and shake issue on V8 - 4 Monaten

I have a set of Theta Kenny Ko 12V servos and have tested them on my TDR THL787H on cyclic and THL782H on tail. Zero issues from first testing with Evo V8 using 8.2V The cyclic servo are P53 and D53 dead 16 The tail is P48 D128 Dead 13 The wag and bobble issues might be more heli specific than servo specific. From customers in the US we have had many bobble issues with the iL Goblin and it

Re: Hobbywing Platinum HV 180A V5 ESC setup with Neo - 4 Monaten

The HW 180 Platinum does not come with a telemetry wire, only the yellow single wire for rpm outputto the rpm port of the Vbar Neo/Evo. You would need to buy the special telemetry cable from HW that plugs into the teleport on the side of the Neo/Evo. Manual here https://www.hobbywing.com/en/uploads/file/20240426/f2e8dad2a4854c8d5fead05690184769.pdf

Re: New Sab 700's with tail bob and shake issue on V8 - 5 Monaten

I have tested full size Theta Kenny Ko edition servos (12V version) on a Henseleit TDF and they work perfectly with V8 with zero issues and have set the refresh rate to 333Hz on the cyclic servos. It might be more heli specific than a servo issue. Have had a few SAB iL Goblin customers that have had similar issues in the US, but no complaints from other makes of helicopters. Maybe try hard mo

Re: slow servos for landing gear - 7 Monaten

The 3 pos MC must drive a CHANNEL cell at the physical output, in the CHANNEL cell is where the delay is set to make the output change slowly. OPTION switches are assigned in the ASSIGN menu under TX settings and then used as input in the 3 POS MC.

Re: OMP M2 EVO mit 7Kanal RX und VBC - 9 Monaten

Hi Yes the VBC will continuously beep to remind you to select a battery. Regards

Re: OMP M2 EVO mit 7Kanal RX und VBC - 9 Monaten

Hi Zalo Please check MC 15 for switch assignment as it might be that your bank switch is coupled to Option 1 switch and in bank 1 it could be in beginner mode and there will be a beep from the ESC to indicate that the heli is in beginner mode. Cheers Peter

Re: vplane back to heli - 11 Monaten

Hi Is this on a Neo/Evo? Then the loading of the firmware was not complete. Select any other firmware for example COPTER and update the Neo/Evo and then select Heli again after the update to load the heli firmware.

Re: vplane back to heli - 11 Monaten

Hi Just load the Heli Pro or Pro/Rescue firmware on it. Peter

Re: Keine Anzeige für Stromverbrauch in VBar für Hobbywing Platinum 80A v5 - 1 Jahr

The HW Platinum 80A V5 does support full telemetry to VBar https://www.hobbywing.com/en/products/Platinum80AV5.html

Re: RS4 - 1 Jahr

The RS4 has a direct drive motor so gear ratio is 1:1 and the motor poles is 42 so half the poles is 21. If you use the original ESC/FBL all in one unit then the governor is already set in the ESC. If you use an aftermarket ESC then you will need to follow the manufacturers manual to setup the ESC for either ESC governor or Vbar governor.

Re: What is the difference between "TELE RPM" and "VBar RPM"? - 1 Jahr

TELEMETRY rpm and rpm read at VBar rpm port.

Starfly ESC - 1 Jahr

Hi With the availability of telemetry for the StarFly range of ESCs, where are they available from as I have found nothing on Google about StarFly? Cheers

Re: Secondary RX Page - 1 Jahr

Hi Rainer All fixed now thanks. Cheers

Secondary RX Page - 1 Jahr

Hi All The secondary RX page https://www.vstabi.info/en/rx2_en shows half English half German and the video does not play. Looks really interesting Cheers

Re: Long Press not available-Orientation - 1 Jahr

Re: Long Press not available-Orientation - 1 Jahr

Thanks Rainer

Long Press not available-Orientation - 1 Jahr

Hi The long press for Orientation in the setup menu does nothing. Checked it with both a Neo and Evo (Pro/Rescue) both without external sensor. This happens on both the VBCt and VBCe. Does it need an external sensor to open up the long press option? It used to open the options irrespective of external sensor fitted or not. All units are fully updated. See attached pic. Cheers

Re: logo 200 battery clip - 1 Jahr

https://shop.mikado-heli.de/e-vendo.php?shop=k_mikado_e&SessionId=&a=search&SearchStr=05412

Re: VBackup deactivation stick position - 1 Jahr

Hi Rainer If the MOTOR is also used on Vplane will this be sufficient? Cheers

Re: Logo 550 SE mit YGE Saphir 125 BEC auf 12V und KST Servos - 1 Jahr

Thanks Rainer, makes sense now.