start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Thank you for your response. Good info to know. A few days before I posted my question I had a motor cut out for a few seconds before it came back on. After landing I looked at the log and it said it had activated failsafe. All electrical wiring seemed OK. I did a range check and a few test flights. I couldn't reproduce the problem but I didn't fly too far away. This is quite an old model,by mahbouni - Fragen VBar Control Touch
When in the Model Status menu and viewng the Antenna status, is the radio at full or reduced power for the range check? My range check at 10m seemed fine but I also flew the model while in this menu and periodically looked at the status as the model went further away. The larger horizontal status bar went below Normal quite quickly. It was definitely less than 100m away. Is that something I shby mahbouni - Fragen VBar Control Touch
That's good to hear. I know there's a chip shortage, so probably things will take time to get back to normal.by mahbouni - VPlane/VBasic VLink
Can the Neo Mini be loaded with VPlane firmware and will you ever sell it separately? I have a few micro sized planes, which it would be ideal for.by mahbouni - VPlane/VBasic VLink
Done, thanksby mahbouni - Questions VBar Control Touch
Started flying at 08:15 this morning and there were no radom clicks. Ambient temperature was about 19C. Now the Sun has risen more and it is a little bit warmer I just started hearing the clicks and feeling the vibrations. So I just did the calibration you suggested and now the clicks are gone completely, even if I move the trim wheels deliberately. Although I'm not using the trims for any helis,by mahbouni - Questions VBar Control Touch
Sure will do, but in my opinion the feedback clicks/vibrations are a gimmick and serves no useful purpose to me. I hope you will implement an option to disable it. Or perhaps just make the clicks further apart, i.e you have to turn the wheel further between each click.by mahbouni - Questions VBar Control Touch
I was about to do the calibration but the problem seems to have gone away. Maybe ambient temperature has something to do with it. I did also update firmware last night.by mahbouni - Questions VBar Control Touch
I'm not using them for anything so I'll try your suggestion.by mahbouni - Questions VBar Control Touch
Any update on this?by mahbouni - Questions VBar Control Touch
I just discovered that either of the 2 wheels at the back cause the same click/vibration if I turn them. I'm guessing it's small movements of the pot that randomly causes it. Can I disable the feedback from the wheels?by mahbouni - Questions VBar Control Touch
Pitch Stick Click is disabled and has never been enabled.by mahbouni - Questions VBar Control Touch
Charged VBCT battery last night and went out for a fly this morning. I can feel random clicks/vibrations in the radio. It even happens when the model is powered off and I can't identify any pattern to it. Sometimes it's one click and other times it's 2 or 3 close together. Moving the sticks or changing the radio's orientation doesn't seem to have any affect. It just happens sporadically. It wasn'by mahbouni - Questions VBar Control Touch
Yeah it's as I thought but needed confirmation of how your charger converts power. I guess some less well designed chargers might waste the higher voltage like a linear bec. As for current my objective is to maximise the energy of my lipo. A 4s 5000 lipo will give more charges than a 3s and maybe I don't even need it to be fully charged. I can leave it at a little bit above storage capacity, sayby mahbouni - Questions VBar Control Touch
If I use higher voltage, e.g 4s lipo, will it draw less current than a 3s lipo? If not then I'll just get a 3s lipo because it's cheaper. What rating of fuse would you suggestby mahbouni - Questions VBar Control Touch
OK, I'm going to make up a charging cable. For the connector that plugs into VBCT, which is positive voltage, outer or inner? Eddi E. aus G. Wrote: ------------------------------------------------------- > Hi, > > please bear in mind that we have a LiPo in the > radio, and calculate the remaining capacity from > the voltage of the battery, amongst other things. >by mahbouni - Questions VBar Control Touch
Flew with my VBCT for the first time today. Starting with a fully charged battery, from 9am until 1:30pm, and after 6 flights the battery is down to 66%. Can I charge the battery at the field from a 12V source, such as a 3s LiPo and an appropriate connector cable, e.g. 3s 8000mAh?by mahbouni - Questions VBar Control Touch
Can you tell us more about the online features like the cloud functions and Android appsby mahbouni - Questions VBar Control Touch
OK thanks for finding the problem for me. I will email Heinoby mahbouni - Questions VBar Control
Yes you are correct. I found the firmware version in VBC and it says 0.65536. However, the YGE PC software says it's 1.03232.by mahbouni - Questions VBar Control
YGE 35LVT. I will have to get back to you on the firmware. Will need to connect to PC to find out. Unfortunately I need to disassemble the helicopter a little bit to get access to the Neo area.by mahbouni - Questions VBar Control
OK, the battery issue was my bad and is resolved now. The YGE settings I can't figure out. i waited a couple of minutes but still the BEC voltage is zero and the gov mode is not set. I think I will have to connect to the PC software to verify what I have.by mahbouni - Questions VBar Control
OK well I will try both and see which I prefer. When I set other params, e.g BEC voltage, the Store menu item becomes enabled and I select that (I guess) to store the values in the ESC. Thing is it always shows zero after I power up the ESC again. Does it not load back the current values?Actually I'm not sure it's changing the BEC voltage at all because I tried 6V just for test purposes but itby mahbouni - Questions VBar Control
Yes, I got to the YGE Auto Setup panel and I have something that seems to be working. RPM displayed is close to that requested in the governor settings, but not sure if I have ESC endpoints setup correctly. Is it possible to use YGE governor? Even if I enable it with YGE PC software VControl seems to set it back to VBar governor. Not sure if I did something wrong in VControl.by mahbouni - Questions VBar Control
I made a cable from a Spektrum sat extension and servo extension. In the ESC setup wizard I could't get the LVT setup to do anything, so I did initial mode setup with the older YGE setup wizard. Is that what we're meant to do or should we do mode programming without the wizard?by mahbouni - Questions VBar Control
MH Wrote: ------------------------------------------------------- > mahbouni Wrote: > -------------------------------------------------- > ----- > > Got my 35LVT and 65LVT today. The adapter cable > > Where did you get the 35LVT? Direct from YGE. Send an email to info@yge.de. Otherwise you can get the 65LVT and Uby mahbouni - Questions VBar Control
Which connector do I need to order for the telemetry? Maybe I can cut a Spektrum satellite cable and make 2?by mahbouni - Questions VBar Control
Got my 35LVT and 65LVT today. The adapter cable for connecting telemetry to Neo will be released by Mikado or YGE? https://www.yge.de/wp-content/uploads/2017/11/YGE-35-65LVT-eng.pdfby mahbouni - Questions VBar Control