start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Evening all, Currently im selling a helicopter that is fitted with a VBAR NEO Vlink and a prospective buyer has asked about setting it up to his Spektrum Dx9 Tx. Is this possible to do by simply adding the satellites to the NEO? Does anyone have a step by step guide on how to go through the process?by p1andy - VBar VLink
Another F3c Vbar flyer here. Have it flying well but do agree with the above suggestions regarding increasing the number of pitch curve points, the ability to raise or lower the curve via a trim knob and also to steepen or flatten the pitch curve via a trim knob.by p1andy - Café
Ignore the above. Looks like I have it figured out. Thanks for the hintsby p1andy - VPlane/VBasic VLink
Ok so I think I have the air brakes working now, only that now they move too far when rudder is applied. Is there a way to limit the travel so the air brake stays at the max limit when going one direction on the rudder stick?by p1andy - VPlane/VBasic VLink
Hi Rainer, Any chance you can break that down further for me? I’m new to the plane side and MC in general. In MC09 what is dely?by p1andy - VPlane/VBasic VLink
Hello, New to setting up fixed wing on Vbar and looking for some assistance in setting up a twin rudder delta aircraft to allow the rudders to be used as airbrakes. Currently the rudders are connected to Tail & Aux3 on the NEO vbasic and i have them working correctly for normal rudder use. What i am looking for is the ability to use the rudders as an airbrake by flick a "flap" sby p1andy - VPlane/VBasic VLink
Gents, I see there are new selections in the new heli wizard that have appeared recently being L scale, XL scale & XXL scale. Can you please advise what the size categories are for each of the new wizards? Also what parameters each of the wizards change? We have a few scale helis setup on NEOs that are flying well, are the new wizard settings worthwhile changing to or should we just leaby p1andy - Setups
Evening Rainer, Thanks for the prompt response. ESC is a castle and is set to external governor. Your second point is where i have been going wrong as no i have not calibrated the 0 collective again. I have never required to do this on a model so far. Can you point me in the right direction on where to do this?by p1andy - Setups
Hello all, I am currently in the process of setting up/tuning an electirc Vario EC135 which is newly built and had two test hovers so far. What i am struggling with is the governor settings as the headspeed is all over the place right now. The heli was initially set up with -10/+10 degrees collective before dialling the pitch curve back in the VBC to achieve -2/+10degrees with 4degrees midby p1andy - Setups
Cant see the point in duplicating the questions, but noted for future. The link is also just the link on how to adjust the curve manually which we already know.by p1andy - Fragen VBar Control Touch
I have the original VBC, can this still be accessed in it?by p1andy - Fragen VBar Control Touch
I would also be interested in this feature for flying F3C to alter the pitch curve from a poti rather than having to amend the points to suit wind conditions.by p1andy - Fragen VBar Control Touch
Ah this is why i cant see some of the VBC forums, can you please activate my user name too Rainer?by p1andy - Café
Sorry the search function has started working, am i correct that i double the pole count and half the ratio?by p1andy - Café
Hello, I am in the process of setting up an electric Vario Bell 230 and in order to set up the vbar governor i am looking to set the gear ratio at 14.29 however the maximum available ratio in the VBC is 12.70. I'm sure i have read somewhere that you can half the ratio and adjust the headspeed to suit but just looking for some confirmation please.by p1andy - Café
I have filled out the service request, what do i do now? Do i await contact or do i send the NEO in for inspection?by p1andy - VBar NEO (non VLink)
It is always run through a BEC so i have just checked it with a 2s lipo direct and it is still showing the same errors. Looks like it will have to be sent inby p1andy - VBar NEO (non VLink)
Sorry but there is not much to see on the logs as it does not boot up, but please see below sample log. VBar Start -- LOGO 550 -- 15.05.2019 -- 18:41:58 18:41:58;1;Reset Reason: Power On 18:42:00;2;Bank 2 Loaded 18:42:00;1;Motorswitch Motor Off 18:42:00;1;Motorswitch Idle Bailout 18:42:03;2;Calibration Finished 18:42:03;3;IMU Sensor delivers no data 18:42:03;4;IMU Stopped delivering Datby p1andy - VBar NEO (non VLink)
Hello All, I have an issue with a Vbar NEO of mine installed in a Logo 550. It was flying fine up until recently when it failed to initialize with warning sounds and flashing red. I have read up about tapping the NEO and reverting it back to pro software none of which have cured the problem. The only thing this has done is broken the tabs on the case of the NEO Does any one have any suggesby p1andy - VBar NEO (non VLink)
Hello, I have a club mate who has recently purchased a Logo 600 and also the carbon frame upgrade but is having issues with the build. The long metal bearing/motor/frame support in the carbon upgrade will not allow the one way bearing to fit in the third main shaft bearing. When trying to use the motor bearing support supplied with the kit it is not possible to install the pinion as it locksby p1andy - Logo 200/400/500/600 Questions