start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
I tested three types of capacitor systems, the first two were straight capacitors one was a Futaba buffer the other was a Racers Edge glitch buffer. Neither worked. I tested the R2 Prototyping Buffer and it did not work as well. Funny thing happened, when disconnecting the lipo from the hobbywing esc with bec and watching the R2 Prototyping Buffer drain down and having an Align tail servo pby weracemo - VBar NEO (non VLink)
RV schrieb: ------------------------------------------------------- > About the Cap - as soon as i have added one single > 16V 4700uF it was gone. I found a Glitch Buster Power Capacitor for six bucks and it looks like I can pull the pins and put them in the two empty holes on the receiver so I won't be taking up another receiver port. Will this work? Racers Edge 2472 Glitch Bustby weracemo - VBar NEO (non VLink)
What size capacitor and where do I put it, power or signal? Found this after some thinking....Ok im going to test an R2 Prototyping Super Capacitor Buffer Unit...... I herd about it for a different reason on heli nation. It is supposed to supply backup power but if it fixes this I'm going to have one on every heli. Good or bad servo im going to have one for safety after seeing the lockups.by weracemo - VBar NEO (non VLink)
RV schrieb: ------------------------------------------------------- > It is a reverse voltage issue of this servos. > > The VLink NEOS have a strong internal regulation - > and the VLink is connected AFTER this item - so we > can buffer bad servos here ;-) > > The NON-VLINK - the Sat is connected here directly > to the power bus where all the servos are > coby weracemo - VBar NEO (non VLink)
+1 I am. Both 2 blades and 3 blades. Works great and very easy to tune :-)by weracemo - Setups
HobbyWing Platinum PRO V4 130A HV ESC (6s-14s) has 10A built in BEC (need programming box also) -Update to latest firmware to get rid of tail kick issue. -Disable low voltage cutout and use Vbar UI sensor with battery logging -Choose Fixed Wing for governor type -Set end points with Vbar setup software by turning on throttle servo adjustment (temporarily), powering up full throttle and afby weracemo - Setups
Goblin 570 log files with BK 8002 servos VBar Start -- Gobin 570 -- 21.06.2016 -- 16:52:14 16:52:15;1;Reset Reason: Power On 16:52:18;2;Calibration Finished 16:54:29;2;Bank 2 Loaded 16:54:33;2;Bank 3 Loaded 16:54:37;2;Bank 2 Loaded 16:54:38;2;Bank 1 Loaded 16:57:30;3;RC Input Packets lost 16:57:30;4;RC Failsafe activated 16:57:31;3;RC Input Packets lost 16:57:31;4;RC Failsaby weracemo - VBar NEO (non VLink)
Greetings my friends, I love my Vbar system (Control and 5 NEO's all are non V-link) but have what seems to be a compatibility issue with Bert Kammerer BK 8002 servos and the NEO satellite. -The BK 8002 servos will work with a NEO V-link model -The BK 8001 servos work fine with all of my NEO non V-link models -The BK 8002 and 3001 servos freeze up with my all of my NEO non V-link models aby weracemo - VBar NEO (non VLink)