start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
I'm starting assembly mine, can I have the new shims for it?by norser - Logo 700/800 Questions
I bought the hard dampers for logo 700 head, but I want to know if I install it inside or outside the head!? There is 3 dampers each side, I need to change all of it?by norser - Logo 700/800 Questions
Someone has tested this motor? what is the opinion?by norser - Logo 700/800 Questions
Hello, someone have tested this motor? what is the opinion?by norser - Logo 700/800 Questions
Hello, i´m assembly a new kit that i bought this week directly to mikado. I need to know if this problem with shims size is already solved or were i can get the shim´s with the size that fits without give me any problems! Thanks for all the helpby norser - Logo 700/800 Questions
Nice, at this moment i have 12/12 and cyclic ring are at 69. With this config the Swash don't bind. I will try the way it works.by norser - Setups
Hello, i have find a way that the swashpalte don't touch in any place reducing in the cyclic ring. I will be try new config this weekend and give you some news. Why you use a bec battery? Have some problems with Kontronik bec? Bestsby norser - Setups
Good morning. I have programming all my helis with vbar without this kind of problems... All is ok... Only bind problems with servo arms in full elevator and pitch movememnts... in all the ways. I will change the servo arms (the ones Gerd Guzicki sent to me are Futaba 19mm) but i think this is not the solution... The servo arms right now are 90 degrees with swashplate. Do you know why this workby norser - Setups
I need to change my servo arms... The ones that Minicopter sent to me is too big! My installation is very similar to yours I only made a wire Job a little different! About speed bank, what is?by norser - Setups
Thanks for the fast reply :-) What is the distance you have in your mikado arms? Because with Diabolo arms they have 19mm from center of the servo, and is impossible to work!!! In full up and down pitch when you input elevator controls they will touch a lot. It's possible a picture from what you have done with spacers in swash guide? What is speed bank? Bests Sergio Cruzby norser - Setups
Hello, I'm with difficulty programming my new Diabolo 700 with my vbar Neo. I have other Helis working very fine with Neo, but with this one the elevator servo are binding in the plate that supports the gyro. Another problems is with full positive pitch the elevator arm are binding the swashplate guide. I'm ising the servo arms that comes with Minicopter Heli, and the geometry of the servo arms sby norser - Setups
Hello, i have opened the VBar control to give more tension to the sticks and i found my cable from the vibration motor (i think is) are disconnected. I only need one picture to check were this cables have the correct position. See picture attachby norser - Questions VBar Control
It´s done :-) Many thanks for the help! I don´t see but i found the answer in another post in this forum. Best regards Sérgio Cruzby norser - Questions VBar Control
I only need a picture from this cable connected (Vibration motor)by norser - Questions VBar Control
The Pin are inside the connector but is done by me after they are off! This is the reason i need to know the correct position for the cables. Best regardsby norser - Questions VBar Control
Can someone tell me or send me a picture with correct connections for this cable? (Vibration motor) When i opened the vBar control to adjust the sticks this cables are off the connector. Many thanksby norser - Questions VBar Control
Dear friend, is not only mine with problems! If you read all the post you will see that is a common problem with kontronik jive pro! You are a lucky manby norser - Café
Many thanks for the reply Eddi. I´m in contact with kontronik to check if they have a solution. But they answer my e-mail with a big surprise factor!!! So, this is happening only with me? Best regardsby norser - Café
Do you know if have some evolution in a problem solution? If I need to upgrade the controller I will need to send it to kontronik or buy a special upgrade cable and check if this cable exist. So resuming I'm seeing that my controller goes... And I will stay 2 weeks without it! It's new...by norser - Café
Hello I'm with a problem when I connect the batteries to the controller the vbar don't start! I need to unplug the motor wire+ auxiliary Bec cable and connect it again with main batteries already plungedto the controller and the Vbar start. That appears that the controller gives a start voltage that is not enough to start the vstabi. Many thanks if someone can help me.by norser - Café