Vbar neo does not run esc scorpion

Hi

I have Trex 700X with vbar neo link, vcontrol touch and esc scorpion 200a.
Until Sunday it was flying perfect.
Today I went to fly a helicopter took off and started kind of punching the tail, I landed, turned off the battery and turned it on again and the esc no longer runs.
Everything works at vbar minus esc.
Any ideas for solving problem ??

Note: I put new vbar neo and everything is working.

Okay - could you please cross check the ESC output socket with a servo?

Please connect a servo to ESC socket (as a kind of a pointer) and see if this moves and has force when "turning on the motor".

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

I put a servo at the exit of the esc, moves and has strength.

Okay - strange. I didn't expect this after your description. Anyway - lets check more ...

Could you please have a detailed look at the plugs, sockets and also try to wiggle/move if there may be a bad contact (NEO and ESC Master)?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

I checked contact, touched the plug does not run the esc.
I put in the new Vbar and esc works.

Okay - is there something different in the VBar Setup? Probably the Governor mode?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> Okay - is there something different in the VBar
> Setup? Probably the Governor mode?

No, the acceleration just stopped working.
I changed to external governor, it doesn't work either.
When I enter the motor collective mode it does not accelerate.
I tested esc hobbywing 60A works.
I put it on the scorpion and it doesn't work
I even loaded setup for another vbar and it works. (socorpion)

RV schrieb:
-------------------------------------------------------
> Okay - is there something different in the VBar
> Setup? Probably the Governor mode?

No help for problem??

Quote:

I even loaded setup for another vbar and it works. (socorpion)

So you have loaded another setup to the same ESC/NEO combo and it works?

could you please confirm and upload both regarding setups here (zip them) so icould have a look too?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> I even loaded setup for another vbar and it works.
> (socorpion)
>
> So you have loaded another setup to the same
> ESC/NEO combo and it works?
>
> could you please confirm and upload both regarding
> setups here (zip them) so icould have a look too?


I loaded other settings and it doesn't work.
Attached is the file

There is no attachment. Probably zip them please.

So ... there is no ESC running when it is connected to the ESC port of this particular NEO?
If this is true, please do a cross check:

- unmount blades
- Program a channel macrocell driven by collective at Ch4 or AUX1 or AUX2 or AUX3 (just straight, select what you like)
- connect master ESC to the output above (model off before)
- stick down
- power on and see if the ESC works now driven by the stick

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> There is no attachment. Probably zip them please.
>
> So ... there is no ESC running when it is
> connected to the ESC port of this particular NEO?
> If this is true, please do a cross check:
>
> - unmount blades
> - Program a channel macrocell driven by collective
> at Ch4 or AUX1 or AUX2 or AUX3 (just straight,
> select what you like)
> - connect master ESC to the output above (model
> off before)
> - stick down
> - power on and see if the ESC works now driven by
> the stick


Hi

I did mixing with macrocells, on all outputs the esc works.
I sent the file again

Okay - so now lets cross check the original ESC output as it is now:

If you connect a servo to the ESC socket - does this move according to the Motor switch or stick driven mode?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> Okay - so now lets cross check the original ESC
> output as it is now:
>
> If you connect a servo to the ESC socket - does
> this move according to the Motor switch or stick
> driven mode?


Yes, a servo moves and has strength.
Servo moves when I turn on the engine key or by collective mode in the governor's setup.
Also move through the macrocells mixing coletive with the esc ouput.

Okay ... strange ... one guess ... might it be possible that the ESC does not arm?
Does it make the beep tones or not at the powerup?

If not ...
Please reconnect the ESC to the ESC out, open the setup panel and dial down the "motor Off" value a bit.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> Okay ... strange ... one guess ... might it be
> possible that the ESC does not arm?
> Does it make the beep tones or not at the
> powerup?
>
> If not ...
> Please reconnect the ESC to the ESC out, open the
> setup panel and dial down the "motor Off" value a
> bit.

ESC emits 2 beeps.
scopion telemetry does not recognize throttle input
Esc works with another new neo vbar.

This photo is an endpoint for esc HW, interesting that changed a lot of the minimum of the throth "28"
Even making an endpoint process throttle the radio, activating collective control and turning off esc and reconnecting with an accelerated stick on the radio

Okay - lets check this VBar in the Service, i am afraid we won't get a solution here online.

Please file a service case by clicking on the service icon at this Vbar in your list.
Add a link to this thread (there is a field) for my colleque please.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

RV schrieb:
-------------------------------------------------------
> Okay - lets check this VBar in the Service, i am
> afraid we won't get a solution here online.
>
> Please file a service case by clicking on the
> service icon at this Vbar in your list.
> Add a link to this thread (there is a field) for
> my colleque please.

Ok

Thank you

RV schrieb:
-------------------------------------------------------
> Okay - lets check this VBar in the Service, i am
> afraid we won't get a solution here online.
>
> Please file a service case by clicking on the
> service icon at this Vbar in your list.
> Add a link to this thread (there is a field) for
> my colleque please.


There I will send without antenna, I used another vbar that was not a vlink