How do I mix elevator from rudder input using a "curved" macrocell?

I would like to implement a rudder/elevator mix function using the "Buddy" switch
to enable this function.

Using this function, I would like to use a "curve" to have the elevator mix
be such that the same pitch(pos or neg) is occurs whether left or right rudder is
applied.

Thanks for your help.

I am attempting to upload my VCT "Setup" file to this thread.

I am attempting to upload my VCT "MACRO" file to this thread.

Attempting to upload setup file and macro file here.

Attempting to upload setup file here.

It appears as if the setup and macro files are uploaded.

I hope this can help in solving the vcurve situtation.

Thanks for you help

Hello gene,

this gets too complicated for me. I can only give you a rough hint, i am no plane pilot and don't have time to dive that deep into your special setup as it would be needed.

The Signals to right and left elev Servo (MC 01 and 04) come currently from MC 31 and 33.

So - in between this chain set a mc for each side. This is a mixer, feed by MC31/33 with 100%. Set MC01/04 input to this mixer cells.

Set one mixer input each of the 2 mixers to a common MC as Multiplexer driven by the switch and position you are referring to.

The MUX cell set another MC as input in the switch pos you want to use.

This Input MC - set as curve driven by FC Tail.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

Hi, RV

Thanks for all your help.

Did uploading the setup and Macro files help at all?

I can understand that this is very time consuming, as I have found.
I didn't realize it would be so complicated.

It looks like I am out of usable macrocells, so I will have to make do.

If I am lucky, the Nuance G2 will not need any rudder to aileron mixing....so
I could then insert a rudder pitch vcurve into the chain.

Then I would have the snap-roll function and the rudder to pitch mixing with its curve.

Sorry to have taken all your time. And many thanks for having done so.

Hello Gene,

yes - the files have been there and i could unzip and load them, otherwise i wouldn't not have been knowing about the used MC's ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

Thanks, RV

Are there any macrocells left that I could use to "insert" a "curve" macrocell in between the MC 1 and MC4
and MC31 and MC33 chain?