Show all posts by user
Chat before, during and after the transmission of VTV -- Begleitender Thread für die Live Übertragungen von VTV
Re: RPM Overshoot with start-Up - 5 years ago
Thanks Rainer, butt what do you mean?? I have the Neo Pro, What do i have manual change?? In the Vbar software or Scorpion software (Scorpion App??in the VBCT) In the VBCT setup screen: Govenor Setup>select> Fully intregrated e-Govenor>Govenor type Scorpion Vbar> Vbar Electric Govenor, you can choose 2 types of govenor,Vbar electric gov or external gov. What do i have toby JDHDienstverlening - Café
RPM Overshoot with start-Up - 5 years ago
Hello. I have a Logo 700 with VBCT and Scorpion Tribunus 14-200 (FW60) scorpion motor HKII-4525-520KV All wire's connect how it should be and can fly with it without problems, butt Overshoots a lott with spoolup RPM values B1 1560 B2 1700 B3 1900 gain 25 standard gear ratio with 13Pinion main 136 10.461 motor 5 pole pairs -10 poles in the flight parameter menu: Govenor Collby JDHDienstverlening - Café
Re: Temperature Sensor - 5 years ago
Hi, did you install the app in the VBCT? and did you run the app updater?? Yesterday i install also my temp sensor and have the same issue and remoeve and install the app and did the app update installer again and it runs ok, now i see the picture in my main screenby JDHDienstverlening - Questions VBar Control Touch
Re: Second Batt in Vbar control Touch - 5 years ago
Thanks Rainer.by JDHDienstverlening - Questions VBar Control Touch
Re: Second Batt in Vbar control Touch - 5 years ago
Thanks Eddi for your reply. So it is not so bad as i think as i see the graph you attached. Butt your explonation is alway good. I will order a second battery from the Mikado side. After charge 1 and charge the other 1 separatly and they are both full, then it is not nessasary to charge it seperate?and can leave the transmitter closed?and charge it together. Thanks againby JDHDienstverlening - Questions VBar Control Touch
Second Batt in Vbar control Touch - 5 years ago
Hello, I recently buy a new VBCT (14-9-2020) and works very good except the battery behavior. I now the Battery consumption is very High Butt so High....Thats not normal i think,its very fast empty for a new system. When Full charge with the wall charger that comes with the set (96%) after a few hour playing with it i have les then 18% (approx total 3Hr playing with it) my battery is aby JDHDienstverlening - Questions VBar Control Touch
Re: Failsafe in VBCT - 5 years ago
RV Wrote: ------------------------------------------------------- > There is a App - BMFA Failsafe App - as the UK > guys also need to show this ... Thanks Rainer, I forgot this app, have install it and works perfectby JDHDienstverlening - Questions VBar Control Touch
Failsafe in VBCT - 5 years ago
is there a possibility to set up Failsafe in the Vbar control touch? My flying club demands that there is a Failsafe capability and I have to show it that this works when the transmitter is turned off and the gas closes!!! to land the model. I don't think you can turn off the transmitter on a bind model?by JDHDienstverlening - Questions VBar Control Touch
Re: VBCT Throttle setup Direct Throttle - 5 years ago
RV Wrote: ------------------------------------------------------- > The "Throttle curve" in the manual bank is defined > by: > > - idle (stick down) > - basic throttle (center) > - basic throttle + collective add (up) Thanks Rainerby JDHDienstverlening - Questions VBar Control Touch
VBCT Throttle setup Direct Throttle - 5 years ago
Hello, a strange question for a new Gasser heli: You can set up 2 different types off set ups for spool up the heli (i have a gasser heli) 1: automatic spool up with the run switch ( explonation like Rainer told in the Setup for a gasser) 2: or to use direct bank in bank 1 for start and spool up and then switch to bank 2 or 3 for flying. i like this setup for start the engine and spby JDHDienstverlening - Questions VBar Control Touch
Re: Anti gravity to a switch - 6 years ago
Thanks Eddi for your explonation..by JDHDienstverlening - Questions VBar Control Touch
Anti gravity to a switch - 6 years ago
Hello, Is it possible to select a option switch in VBCT to switch in 1 bank to 3 differt vallue off antigravity??(see some pilots on Yutube that they fly and switch in different parameters in heli flight in just one bank) do i have to do this option in Macrocell?? but how?? I would like to have 3 different parameters in just one bank. later off course in all 3 banks with different valluesby JDHDienstverlening - Questions VBar Control Touch
Re: Delete files in VBCT - 6 years ago
Thanks Rainer, problem solvedby JDHDienstverlening - Questions VBar Control Touch
Delete files in VBCT - 6 years ago
Hello VBCT users, How can i delete my setup files under tab Modeltools?? I have store some setup files in my VBCT butt would like to remove this. I have in the VBC-T Cloud remove all files butt can not remove it in the VBCT controller. i have save 2 file in my controller , when i touch load set up there are 2 file's stored and in save set up there are also 2 files butt i would like tby JDHDienstverlening - Questions VBar Control Touch
Re: VBCT Throtle cut in Gasser - 6 years ago
Found itby JDHDienstverlening - Questions VBar Control Touch
VBCT Throtle cut in Gasser - 6 years ago
Hi, new on VBCT butt not on Vbar control classic. Butt where can i find the throttle cut switch?? The VBCT is standard and can not find this function I have a Zenoah gasser and the kill switch is remove'd from the engine because the StatorGator sensor is connected on this killswitch. In my Vbar control classic (with my Nitro and Gasser) i can use a switch for throtle cut butt can nby JDHDienstverlening - Questions VBar Control Touch
Re: VBCT Tail set issue - 6 years ago
Thanks Rainer, So you recomment that i must use the internal sensor in the Neo and not use the Silverline sensor.... I was thinking and read somewere that on a gasser its better to use a separate Silverline sensor...to the Neo,butt thats wrong information??? I just did a try again to remove the ext sensor and the servo stays in the middle, so putt everything out and connect the ext sensby JDHDienstverlening - Questions VBar Control Touch
Re: VBCT Tail set issue - 6 years ago
Yes, I turn on first vbct then the gasser heli. When I turn on idle so the vbct connect automatically it's the same Yes I have install a separate silverline sensor. Because it's a gasser with more vibrations, I was thinking that's better, today I will binding my other neo in the logo700 and see what happens I have upgrade my neo to 6.4 with control manager with the boot plug butt pc USB softwaby JDHDienstverlening - Questions VBar Control Touch
Re: VBCT Tail set issue - 6 years ago
Hello Rainer, before i post this topic i did off course a stick calibration,recalibrate,butt with no effect all sticks are at 0 midstick even i try a other servo and this servo is also running to 1 sideby JDHDienstverlening - Questions VBar Control Touch
VBCT Tail set issue - 6 years ago
Hello, Today i was start to setup my new VBCT, Before i use a VBC classic and Vbar Neo on a Gasser and no issues Today on the bench my tail servo go from left to right without input do i centre it, it goes back to the end right. With the VBC classic i dont have this Whats happening?? Normal you dont have to do a new set up and all parameters are programmed in the NEO. so is thisby JDHDienstverlening - Questions VBar Control Touch
Re: Wifi in VBCT - 6 years ago
Hello Eddi, I dont see a filter in the TP-Link Deco MESH system. The Vbct see my MESH router and now and connect with a red dot (takes a long time) butt its connected en red point. When i go to the Wifi control tab i see only a Channel and not a mac adres and when i go to the shop tab the QR picture is black and can not go in to the shop,butt it's connected to the MESH router. All other dby JDHDienstverlening - Questions VBar Control Touch
Re: Wifi in VBCT - 6 years ago
I use also 2,4 and 5ghz I switched 5 out and still don't give me a connection Vbct find my mesh wifi butt still stays yellow and not a red dot. And with no red dot it is not possible to go online to the shop etc. All other devices I use work perfect with the WiFi mesh only not the vbct Only the vbct works with my smart phone or my master router Its Stange butt in the WiFi tab on vbct Iby JDHDienstverlening - Questions VBar Control Touch
Wifi in VBCT - 6 years ago
Hello, today i recieved my new VBCT. Looks nice and did the Registation on Vstabi. Now i have a Main master Wifi router(incomming from outside on the downfloor) and with connected 3 Mesh wifi systems for everywhere/level in the house Wifi. It work on all my devices i use (smartphone,TV,PC,Laptop etc)butt NOT on the new VBCT. VBCT find the Mesh router butt not connected with a red poiby JDHDienstverlening - Questions VBar Control Touch
Re: Logo 200 - 6 years ago
Hi, I read with the new Logo 200 there are a Battery included, What kind off Battery (size etc etc)and can you buy it on the Mikado webshop?? I dont see it on the Mikado site. What is the flighttime off this battery??by JDHDienstverlening - Café
Logo 200 Battery - 6 years ago
Hi, I read with the new Logo 200 there are a Battery included, What kind off Battery (size etc etc)and can you buy it on the Mikado webshop?? I dont see it on the Mikado site. What is the flighttime off this battery??by JDHDienstverlening - Logo 200/400/500/600 Questions
VBCT Case - 8 years ago
Hi Have the VBCT the same Case size like the VBC? I have my VBC in a "pult" and possible i buy a VBCT also for replace the VBC Regards Jeroenby JDHDienstverlening - Questions VBar Control Touch
Re: Black screen by startup VBC - 8 years ago
Hi Andy from Sandy Thanks for this tip!! Regardsby JDHDienstverlening - Questions VBar Control
Re: Black screen by startup VBC - 8 years ago
Hi Eddi, Thanks for your reply, I have made a request on the Mikdao Site butt you can cancel this request (RMA ID 23610) I dont like open the case and do it your self(warranty) butt when i can turn it on and hold it to my body and it works that will be ok for me. The problem is also when i start it up and have no screen it is difficult to put the VBC off.... Have Fun on IRCHA Bestby JDHDienstverlening - Questions VBar Control
Re: Black screen by startup VBC - 8 years ago
RV Wrote: ------------------------------------------------------- > > At the end - it is only the display controller > which does not start, the radio itself is starting > and safe. Turning on while covering the sensor / > controller chip area will start the display > correctly. Thats correct every things work butt dont have a display. I covering indeed with my finby JDHDienstverlening - Questions VBar Control
Re: Black screen by startup VBC - 8 years ago
Hi Stephan, I dont have shadows on my flying spot! Now i turn the VBC on with my finger on the light sensor (under the display) I go Emigrate to South Amerika soon and its verry sunny over there and i hope this can be fixt,but how? The VBC is very new and 3 time use outside I hope Mikado can help me solved this issueby JDHDienstverlening - Questions VBar Control