start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Thanks will let him know.by Vinger - Questions VBar Control Touch
Hi A friend of mine wants to use the Aerospire MultiGov on his nitro heli. As this needs the traditional throttle with curves and an additional channel to switch the rpm target, how would one use the Neo in external gov mode? So with the throttle output from ESC port, and say AUX2 as the rpm select channel, and still using the bank switch to demand the three modes of operation. Now to get tby Vinger - Questions VBar Control Touch
That is just my signature. The helis I own and fly.by Vinger - Café
Latest firmware on ESC? Correct settings in ESC for protocol and governor?by Vinger - Café
Hi I had the same oscillations after an elevator input. Contacted Jan about it and here is his explanations. Regards Hello Peter, what you see is that the fuselage oscillate about 1 to 2 times after a hard stop. The reason for that is that there is a little play from about 0,1mm between the plastic bush at the rotor shaft and the hole of the rotor hub. Also think about the lightby Vinger - Henseleit Rigid
RV Wrote: ------------------------------------------------------- > Not yet - but i personally would go a opposite way > and drop all the single flags in all the apps. I > would vote for a "general flag" in the VBCt which > lets the user decide once at the general settings > if he wants to have metric (which is the > international ISO standard) or imperial dimenby Vinger - Café
Any update on this? Would also like to have altitude in feet and speed in km/h.by Vinger - Café
Hi VBC had no way of hardware resetting and I really like the idea that the TX cannot switch off while connected to a RX. So does this then reset the VBCt to factory default as you say it is a hardware reset? Thanks Peterby Vinger - Questions VBar Control Touch
Hi Rainer It is not a matter of removing the button, but locking it in software while a Neo is connected.by Vinger - Questions VBar Control Touch
Just use a VBasic, the gyros are not available although all the functions for Vplane are.by Vinger - VPlane/VBasic VLink
Hi Eddie According to the manual the geometry correction was disabled from initial setup. Will check again. Yes optimizing flights were done and redone after each change to the main rotor settings. Will get the setup file and post here later today. Peterby Vinger - Setups
Hi I am stumped by the tendency of my TDSF to have an oscillation after a quick elevator input. Have tried increasing main rotor gain but it has no effect. Set the heli size to 30 which made an improvement but still oscillating about 2-3 times. Aileron quick inputs are rock solid. Setup is default as per Jan's recommendation, MKS mini servos, Kontronik power package and the super light bladeby Vinger - Setups
Thanks RV will let him know.by Vinger - Questions VBar Control Touch
Again helping a user with his VBCt. It switched on and gave the screen with a choice "Start Check, format disk, etc" He selected check and it then went to a white screen and now completely unresponsive. Is there a way to let VBC Manager or WiFi rebuild the file system?by Vinger - Questions VBar Control Touch
https://www.vstabi.info/en/node/1784 The channels are indicated on the screen, ELEV=1, RUDDER=TAIL, AIL L= 2 Ail R=3 and THROTTLE is ESC.by Vinger - VPlane/VBasic VLink
Yes same guy thanks for helping him outby Vinger - Questions VBar Control Touch
He wants to have higher volts as he has a HV throttle servo. Thks RVby Vinger - Questions VBar Control Touch
Helping someone with a Silverline Vbar with sat on a nitro helicopter. Can the throttle servo be changed to channel 4 like one could select in the V5.3 firmware?by Vinger - Questions VBar Control Touch
alparmer Wrote: ------------------------------------------------------- > The only thing I was able to do was upload vstabi > recovery. However, I believe this is not a > working firmware. I can connect the vbar but > cannot update or do anything else. After recovery you need to load a flying firmware, either V5.3 or V6.0 for VBC use. Follow the videos linked earlier on howby Vinger - Questions V5
Thanks Rainer.by Vinger - Questions VBar Control Touch
Hi Rainer The question is really that one could assign any parameter on the VBC to a knob to enable in flight tuning but not on the VBCt. I quote from Helifreak tried assigning Basic Throttle to a slider (wheel) and no joy, doesn't work. I have the PAR LOCK set to UNLOCK MODIFY. "pot1" which is assigned to Main Rotor Gain (as a test) through the Switch Assignment app and it woby Vinger - Questions VBar Control Touch
Videos here https://uroehr.de/vtube/cat/english-videosby Vinger - Questions V5
So a slider can be used?by Vinger - Questions VBar Control Touch
How does one assign a knob to min throttle in the nitro governor to enable tuning in flight?by Vinger - Questions VBar Control Touch
Eddi E. aus G. Wrote: ------------------------------------------------------- > Hi all, > > can anybody confirm you see the stream? > > Cheers > > Eddi Nope only a video format not supported.by Vinger - VTV
1. Can you explain the oscillator cell in more detail as well as examples on how and where to use it? 2. If macrocell setup was created on a VBCt with naming the cells, will this work on a VBC if the Neo is now bound to a VBC. Vice versa as well, if changes to a setup is done on a VBC with macrocells is the changes now reflected if the Neo is bound to a VBCt? Regards and thanks for the suppby Vinger - VTV
Preacher Wrote: ------------------------------------------------------- > Yes the logbook app is installed in my friends > vbarcontrol the battery choice popps up as soon as > he > makes the connection if i trie to do this with my > vbar control touch it start the connection to the > heli and i can fly the helicopter. > But it does not pop up with the choice of >by Vinger - Café
jerrykirwan Wrote: ------------------------------------------------------- > RV, > > I put the jumper in and went to Control manager > clicked on the bar, logged in and assigned the neo > to me it shows up in my devices as OK it shows > basic programing > > Yes, I down loaded the key file and found it in my > downloads file > I then moved it to my deskby Vinger - VBar NEO (non VLink)