start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
This is not possible - you need to assign a physical switch to the logical option switch.von RV - Questions VBar Control Touch
Just add the satellites, enable spektrum with the PC software, bind it with the PC and setup the radio as stated here: https://www.vstabi.info/en/neo_transmitter The hardes thing for the 3rd party guys is to set up their radio - we just need simle 4 gimbal signals (H-1) and some direct switching channels (Bank, Motor, Rescue) - but thats the tricky part where we can't assist.von RV - VBar VLink
Also beim Firmwareupdate. Naja - hast Du denn sichergestellt dass nichts am CP dran ist? - Also noch kein Sat angesteckt ist? Ansonsten - mehrmals testen, ggf mal Windows im abgesicherten Modus mit Netzwerk probieren, USB hub ggf. nehmen / nicht nehmen. Wenns dann nicht geht ... Service Fall eröffnen.von RV - Questions VBar Control Touch
Eigentlich ist alles in diesem Video hier erklärt: https://uroehr.de/vtube/cat/vbar-control-klassik/video/stabi-de Wo genau hängts denn da an welcher Stelle? Was bei VBCt/Evo dazu kommt ... die Apps für Altstabis im Shop müssen extra geladen werden.von RV - Questions VBar Control Touch
Das Heckservo wird nicht getrimmt. Das macht der Autotrim. Wo möchtest Du das Heckservo trimmen? Da gibts keinen Schieber für. Screenshot mal bitte ;-)von RV - Fragen VBar Control Touch
Please no double posts! Proceed here, but watch the video linked above carefully and tell us a bit more if you still can't do it. Being lack of a useful description what did you do, what happened, what did you expect, probably a screenshot - there will be no answer.von RV - VBar VLink
Hello, in short words - those old devices are basically out of service ... Self enable with the license key which has already been sent out by email today. Keep note it is only valid for 24hrs - after this get a new one and use it. Then update online. https://uroehr.de/vtube/cat/old-v5-vbars-archive-/video/vbar-online-update More Videos => V5 Archive and/or VBC classic sectionvon RV - VBar VLink
Dann mach einfach das was dort stand. Kontaktiere den Service per Mail oder lege einen Servicefall an. service(at)mikado-heli.de www.vstabi.info/rmavon RV - Fragen VBar Control Touch
Ok - so it is definitely a issue with the NEO. Please file a RMA at the login section of vstabi.info, my colleque will reply then tomorrow. https://www.vstabi.info/en/rmavon RV - VBar VLink
Du hast doch um 2024-03-24 20:11:30 einen FW Download machen können? Du hast Dir V6 freigeschaltet (und warum auch immer 2 mal) - aber V5 geladen. Probiers nochmals, Du hast noch 20h und 2 Versuche frei - ansonsten siehe Video für Altstabis zum self-enable: https://uroehr.de/vtube/cat/alte-v5-vstabis-archiv/video/vstabi-online-update PS: Die Vorgehensweisen waren damals dieselbevon RV - Café
Hmmm ... there is nothing wrong with this device. Could you please try to bind another NEO/EVO - so we are sure it is something with the NEO and not with the VBC?von RV - VBar VLink
Dann schau mal ganz genau meine Anweisung im PC Software Installations Video zum Treiber an. Ich gehe davon aus dass Du die Video Seite im Archiv für Altstabis kennt? https://www.vstabi.info/de/v5_videos Das 1. Video bitte mal anschauen, Treiber installieren und wenns nicht geht - ist hier vermutlich End of Lifetime, der Support für diese Geräte ist ausgelaufen. Achja - wichtig ist auchvon RV - Café
Da ist schon eine V6 drauf - und die deaktiviert - wie in meinen Videos gesagt - die USB Funktion. Insofern: Binden mit VBC und ex. VBC Sat, registrieren mittels VBC Screenshot und Benutzen. Wenn Du unbedingt USB brauchst => Recovery Prozedur https://uroehr.de/vtube/cat/alte-v5-vstabis-archiv/video/recovery-devon RV - Café
Das ist noch ein Relikt aus der alten VBC - ist hier nicht umgesetzt da es viel eleganter geht ;-) Nimm die "Parameter Modifizieren" App und weise damit einen der 6 Drehgeber relativ dem Leerlauf zu. - Die Zuweisung ist dann relativ, beim Einschalten wird auf genug Weg geprüft falls der Poti im Eck hängt und erinnert - Es ist dann immer Bankabhängig, musst dann im Idle Mode auvon RV - Fragen VBar Control Touch
Hallo Bernd, Da hier nicht klar ist was es denn genau sein soll ... V6 Firmware für die Stabis: Self-Service - siehe Videos zur VBC Classic damals. https://www.vstabi.info/de/node/1649 - letztes Video. PC Software V6 für Altstabis: Gibt es nicht. USB ist da auch nach Update auf V6 Disabled. App für VBC: Die Apps für Altstabis sind im Shop auf der Anlage ganz unten, müssen instalvon RV - Café
Just watch my videos ;-) https://uroehr.de/vtube/video/vbct-jetcat-ecuv6-en at 10:30 ;-)von RV - VBar VLink
Hello, there is a threshold for the ECU Voltage in the JetCat Panel at the bottom which needs to be set up ;-)von RV - VBar VLink
Having a VBar Control classic, touch or EVO ... load the EVO App for the Add-ons and install Pro or Recue on the VBar EVO ... then ... have a look ;-)von RV - Questions VBar Control Touch
Naja - dazu nimmt man dann einen optisch/elektronischen Drehzahlmesser. Ansonsten - Basisgas in manueller Hochlaufbank erarbeiten - da sieht man die RPM, Gov ist aber aus.von RV - Fragen VBar Control Touch
ich würde es so machen: Bank1 - ohne I Bank2 - 10 Punkte auf allen Achsen Bank3 - 30 Punkte eben dann Und damit testen gehen. Dann hast Du immer eine Umschaltmöglichkeit wenn es sich komisch anfühlt.von RV - VPlane/VBasic VLink
Der Integral soll quasi als "Feintrim des Tages" das Modell in der Spur halten. Da sind so max. 10-30 als Haltewinkel nötig, bei reaktiven Maschinen eher 10 statt 30. Wenn Du zuviel hast steuert sich das Modell etwas "Gummiartig" um die Mitte.von RV - VPlane/VBasic VLink
Min Throttle is the throttle openening which will be the lowest one when Gov is active. More here: https://www.vstabi.info/en/node/2030 RPM Range is a value to allow RPM >4800 1/min used on some smaller helis as a multiplier for the RPM in the VBAR Gov. Usually 4800 should be enough.von RV - Café
There are some files missing on the VBC. Please do a online update. If (new flight) the messages are still w/o text - force a complete reload by: - Toggle to DE - Online Update - Toggle to EN - Online Updatevon RV - VBar VLink
Macrocell outputs are running 72 hz defaultz which is not changeable. The rate for tail and swash servos (swash with VBar EVO) can be changed in teh model setup on the VBCt/e (VBar EVO App needed for VBar EVO rates) .von RV - Questions VBar Control Touch
Also eher ein Nick-Nachpendeln. Das kann eine Ursache in nicht ganz passenden Optimiererwerten haben bzw. könnte zuviel Empfindlichkeit oder zuwenig Style anliegen. Wegen des Aufbäumens - da ist vermutlich der Weg für Nick dann zuende. Weniger Pitch bzw. eien Anpassung der Aufbäumunterdrückung an die Pitchwinkel (s. Hilfe in VBC dazu). Wenns dann noch ist ... ist halt der Weg zuende, Dvon RV - VBar VLink
So - if you only need a switch which gives the right signal w/o delay etc - i'd use a 3-Level. Set up AUX2 as 3-Level, assign the used Switch in the list as input and assign a % Value for each of the 3 Switch positions. If you would like some delay and/or a defined failsafe - we need to chain 2 cells. First add the config above to a cell w/o a aoutput (e.g. Cell 30). Then in AUX2 set up a chavon RV - Questions VBar Control Touch
Das kommt immer an AUX1 raus ;-)von RV - VPlane/VBasic VLink
Hallo Dennis, wir brauchen dazu halt beide Email Adressen. Alt und Neu. Hast Du mir diese?von RV - Fragen VBar Control Touch