start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
I relearned the ESC's with increased minimum throw and all Ok now. Tomorrow will do a maiden flightvon Igor Nack - VCopter VLink
How I can decrease lowest RPM in Motor RUN mode, Uli? Too high RPM to stay on the ground in this mode.von Igor Nack - VCopter VLink
All OK. NEO works fine. Thank you very much again, Uli, for your help and support!!!von Igor Nack - VCopter VLink
Thank you very much, Uli. I will test your setup file tomorrow in the morning and report about result.von Igor Nack - VCopter VLink
Ok. Here my setup file. I have T-Motor F40 2500 motors and Air 20A ESC the same brand.von Igor Nack - VCopter VLink
Did not help anything. I tried to make a new setup, download copter firmware again, erase Macrocell, updated VBar Control and NEO to the latest version... All on the same position. In Test mode all OK with throttle without any problems. I tested to change Idle value from -120 to 120 and Motors RPM changed according with value from min to max. But after Motor RUN I have full throttle value on allvon Igor Nack - VCopter VLink
My VBar, which I installed on this copter was in Macrocell Extender mode before it. It looks like some Cells have some values in Cells, but Cells is empty.von Igor Nack - VCopter VLink
Uli, I already tested reaction without props. Without any changes with motor rpm - all motors at full power. That is why I bit afraid about it. On 3D Quad Ninja was all Ok and even if you switch Motor On you can see a reaction on movement.von Igor Nack - VCopter VLink
Hello Uli, Rainer I built race quad for tests and found one problem which already was published on German language. Regular motors and ESC for copter. Made a Throttle limit setup. All Ok when Testmode Active. All motors are fine. Idle Ok too. But after switching Motor to RUN I have a maximum rpm without any reaction from Throttle stick. I tried different steps but didn't find a solution. On 3Dvon Igor Nack - VCopter VLink
So, maiden flight done. It was first flight on EDF Jet plane for me. But it was cool. A am absolutely happy how NEO works on this plane. Mini Avanti S maiden flightvon Igor Nack - VPlane/VBasic VLink
Hi René, I will do it, not a problem. But we have so rainy weather at the moment, so my plans for maiden flight on this weekend under big question ;-(von Igor Nack - VPlane/VBasic VLink
I made a shot videos how it works on real plane: LG and Door sequencer: https://youtu.be/O1BIaSzp-oY Flaps: https://youtu.be/4jI3z6rUm5gvon Igor Nack - VPlane/VBasic VLink
My setup files for Macrocell and Mini Avanti S modelvon Igor Nack - VPlane/VBasic VLink
RV Wrote: ------------------------------------------------------- > And Igor - i am very curious to see this working > here on my bench! - Can you please share the > Vplane and Makrocells setup file as zip here? > > (my neighbour gets the servos tomorrow for me ...) Will do it tomorrow.von Igor Nack - VPlane/VBasic VLink
RV Wrote: ------------------------------------------------------- > One note on the Flaps: > > In your solution you use 2 others as 3-Level for > the switch. This can also be done by one 3-Level - > used on both Outputs as Input. Center and > endpoints are set in the output channel cell then > to equalize both sides. I decided to use 2 Cells as 3-Level because I wvon Igor Nack - VPlane/VBasic VLink
6. Steering for front LG. - I made the same setup as described Rainer, but added different steering range for Takeoff/Landing and movement on the runaway. To do it I added two additional Cell 36 and Cell 37 where I define steering level from Tail signal, next I added Multiplexer Cell 38 (Input from Sw Op 2, the same as for Flaps) and Mixed this Signal together with FC Tail signal in Cell 32. Thvon Igor Nack - VPlane/VBasic VLink
- Now Front LG. It connected to E1 CH3 Extender channel. We need a delay for open/close LG for correct Doors open/close procedure. E1 CH3 channel has an Input from Cell 31 which setup as Trigger (Input from Sw Op 1) and has delay more than delay, which we setup in Doors channel.von Igor Nack - VPlane/VBasic VLink
5. LG retracts and door sequencer - It was really interesting for me. When I began to setup this plane, I was not sure I could generate Door sequencer function. However, I have done it. - First and important part is front LG doors, because we need following function for front LG and doors open and close: Doors closed (Normal position) Doors open and delayed front LG opens after delay,von Igor Nack - VPlane/VBasic VLink
4. Flaps - I have CH 1 and CH 4 for Right and Left Flaps. Both channels have an Input from Cell 27 and Cell 35 accordingly. Cell 27 and 35 have Threelevel setup which controls via Sw Op 2. Therefore, we have 3 flight modes for Flaps (Flight, Takeoff and Landing). Flaps angle changes according with 3 levels on both Cell 27 and Cell 35.von Igor Nack - VPlane/VBasic VLink
3. Ailerons - The same basic setup as for Rudder – default channels Ch 2 and Ch 3. According with Mini Avanti S manual, I added 10% differential setup for Ailerons.von Igor Nack - VPlane/VBasic VLink
2. Rudder - Here all clear. I have basic Tail channel for Ruddervon Igor Nack - VPlane/VBasic VLink
1. Elevator - We have one servo on every part of Elevator. I decided to use 2 Extender channels because I would like to have separate setup for Right and Left Elevator parts (0 and end points). Input on both channels is FC Elev because we need Gyro Banked setup for Elevator.von Igor Nack - VPlane/VBasic VLink
Hello, Just finished to build Mini Avanti S EDF Jet from Sebart with two NEO's on the board. It was interesting to understand how Macrocell works, setups on concrete example. So, I will try to explain my setup. First, some photos outside and inside of a plane. I changed a bit some parts already included in the kit, because I prefer to have excellent setup for every models. Now about setup.von Igor Nack - VPlane/VBasic VLink
I have Vbar Silverline 6.0 which was in VBar Control kit. I needed to downgrade this Vbar for my customer to 5.3. I made a recovery procedure successfully, but can't make online update to 5.3. I have only two options in Online update: 5.3 Pro which not active and 6.0. If I click license request I have notification: Serial number not valid. How I can decide my problem?von Igor Nack - Café