start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
I recently purchased a second hand Mini Vbar V5.3.4 Serial 1510015990 and changed ownership. Setup Vstabi shows that it is running Express and i would like to load the Pro version. I go to Online Update, select Version 5.3 PL 4 Pro and click Infos.. This takes me to the Vstabi site which says "This device has already a V5 pro license!" if i try and purchase directly on the Mikadvon johnpssa - Questions V5
Hi All, All servos move in the correct directions for aileron, elevator and collective. This only happens in flight mode in setup mode all servos respond as expected. At low collective, ailerons left or right the elevator servo inputs forward elevator. At mid collective there is no elevator response. At full collective, ailerons left or right the elevator servo inputs backward elevator.von johnpssa - VBar NEO (non VLink)
Update, It appears that I have managed to get the servo working. Setting the idle/bank 1 to a flat line above 66% and selecting throttle direct appears to work. Feels odd having a normal curve 70% - 70% I assume the actual curve is coming from the Neo. I would be grateful if you could confirm that this is how it should work. Regards Johnvon johnpssa - VBar NEO (non VLink)
Hi, hope you may be able to help. Vbar Neo Pro with Futaba Sbus and T7C transmitter. Setup as Vstabi information, banks linked to idle up switch, throttle hold and cut working. When I set idle/bank 2 and 3 to flat line curve above 66% throttle servo creeps as expected. The only issue is throttle direct, I have this selected for idle/bank 1 and set for linear 0 - 100 curve. When I move thvon johnpssa - VBar NEO (non VLink)
Hi Rainer, You were correct, thanks for the advice. (Should have turned the magnet over) Regards Johnvon johnpssa - VBar NEO (non VLink)
Thanks Rainer, I did try and would say nothing happened but may be i way not slow enough. Will check and report back. Johnvon johnpssa - VBar NEO (non VLink)
Hi, Vbar Neo upgraded to Pro and nitro governor activated. Magnet sensor indicator is always green. (In main screen and Gov.II with or without sensor connected. Regards Johnvon johnpssa - VBar NEO (non VLink)
Hi Eddi, latset update. There has always been a 0.5mm radial movement in the tail blade grips, so I thought I would check to see if I had got something wrong. I did not find any issues, no missing bits and all correctly fitted, I had some spare blade grips so I gave them a try and the radial movement was much reduced, do not know why as I used the same hardware that I had removed. No sign ovon johnpssa - Logo 200/400/500/600 Questions
Hi Eddi Thanks for the information, given all my efforts on the tail, with little or no change, I was just wondered if I was looking in the wrong place. Amplitude at the bottom of the fin is 3 or 4 fins in width although it is a blur I do not think it is very high frequency, you can almost see the 3 fins. Only other thing is that it seems to start a few seconds after the helicopter lifts ofvon johnpssa - Logo 200/400/500/600 Questions
Hi Eddi, thanks again. It does seem like a resonance issue, from what you have said it is most likely to coming from the tail are there any other areas worth looking at? The Logo flies beautifully, there are no signs of any issues apart from the fin. I will see what I can do regarding the vid although it will not be until the weekend. Regards Johnvon johnpssa - Logo 200/400/500/600 Questions
Hi Eddi, thanks for the response. For the Vibration analysis tail blades are fitted, I only remove the main blades and disconnected the tail from the servo so it can centre. Last Saturday I replaced the shaft, hub and flange bearings, refitted the grips but there was no improvement. As I said it might be OK for a few outings and then it returns. The aluminium tail clamp in my last postvon johnpssa - Logo 200/400/500/600 Questions
Hello, I am running a Logo 550SE (50 flights) flying sport aerobatic with 1750rpm on the head. I have an intermittent but persistent vibration on the vertical tail fin 3 or 4 fins in amplitude After a 7 minute flight the Vbar log shows only 3 or 4 raised vibration warnings. The Vibration analyser (No main blades) shows the head, tail, and motor RPMs all below 40. I have rebuilt the tail butvon johnpssa - Logo 200/400/500/600 Questions
I have recently purchased the aluminium tail rotor clamp (05128) for my Logo 500SE. This item is 26.5mm, the tail rotor spacer set is for 27mm wide to match the setting dimension for the plastic tail rotor clamps. Just wondering if anybody has experience of the aluminium clamp. Thanks in advance, Johnvon johnpssa - Logo 200/400/500/600 Questions