start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
I asked about negative paddle sim because I have tried it for an F3c setup. You are correct. It gets very "heavy" with any setting over -30. But, it does help when sensible values are used.by Fly X Cell - Setups
Are these going to be available for this season or is this more like a fall release item?by Fly X Cell - Café
Is there and estimated release date? More than a month?by Fly X Cell - Café
Does this mean that Vcontrol will not be released until 6.0 is ready?by Fly X Cell - Café
I could have done testing again. You should have sent me a V Control.lolby Fly X Cell - Café
Well that's good to know RV. I didn't think that the nitro gov would go away. I was just concerned about idle adjustment without trim. I suppose knob assignment would suffice.by Fly X Cell - Café
There is no trim on throttle. So what are nitro guys supposed to use?by Fly X Cell - Café
Fixed. My date and time was incorrect on my system and was causing security certificate errors.by Fly X Cell - Questions V5
I am getting an access denied error when trying to login to the license manager.by Fly X Cell - Questions V5
Should we all go back to 5.2?by Fly X Cell - Questions V5
Greetings, Could someone from this forum go over to RR and address this thread? http://rc.runryder.com/helicopter/t698167p1/ I would take care of it myself but if you are know to be sponsored by just about anyone, you are not taken seriously. Also, sometimes your are pinked, deleted, and even banned by Mark.by Fly X Cell - Questions V5
If you are using banks, just remember that throttle servo direction needs to be set for all of them.by Fly X Cell - Questions V5
@Costas, While I was beta testing with this setup on the 5.1 back in December, I had experienced a similar problem with the head speed. What was discovered after completely turning the governor off was that at 50% throttle the head speed was way over anything that I would have requested. Actually, I already knew that from setting up previous governors. This presents as a problem when using fixby Fly X Cell - Questions V5
@MrMel, I have tested it both ways and have NOT experienced any problems banked or not banked. One gentlemen at my field had an issue with banked files when he upgraded and the problem was found to be in channel assignmet page.by Fly X Cell - Questions V5
@GootyS I am using 5.2.4 and there is absolutely NO problem. My 2 previous post did address beans07's problem. It seemed to be a setup issue with wrong channel set in th receiver page. Please do not feel apprehensive about using the gov on Vbar 5.2.4. If you have any issues, post them here. Everyone is here to help.by Fly X Cell - Questions V5
Oh, I see it. Take a look at the receiver page. Aux2 is set for 2, which is the same as Aileron. Set it to 7 which is your rpm request channel.by Fly X Cell - Questions V5
Quote:The preset ch (7) hangs at 0% - are you sure there will be a value >0% by TX command? I noticed the same thing. @beans07, Why are we seeing 0% on channel 7 for all 3 of your banks?by Fly X Cell - Questions V5
BTW, if you decrease your spool up speed to get to rpm quicker, it seems better.by Fly X Cell - Questions V5
RV, I get the same thing on my Furion 6. Blue Sensor version. It is a resonance thing as you said. On some days, I can just adjust the mesh ever so slightly and it will go away. But, at different ambient temperatures it may come or go. For me it happens at the exact same rpm every time.by Fly X Cell - Questions V5
Did you ever get this solved? My Furion 6 does the same thing. And it does it at the same rpm every time.by Fly X Cell - Questions V5
Greetings, Here are my serial numbers: 1400018855 1500010606 1400014178 1410023143 Regards, Clarenceby Fly X Cell - Questions V5
Sent you pm. Stratus Fury 55 Aurora Kasama Srimok Clarence L. Creer III Team HeliWholesalerby Fly X Cell - Questions V5