start && end > -1) { if (start > -1) { var res = data.substring(start, end); start = res.indexOf('>') + 1; res = res.substring(start); if (res.length != 0) { eval(res); } } cursor = end + 1; } } } //]]>
Hi Rainer, all good, did some reading and updated Neo to pro and found parametersby Klinger - Logo XXtreme 700/800 Questions
Hi Rainer, well I tried adjusting the collective & cyclic add right down low with no change in result. So I've put a Neo in it and now trying to figure out how to load the 800 preset without a VBC. I'm running Futaba Sbus so don't have a VBC, is there another way to load heli presets? thanksby Klinger - Logo XXtreme 700/800 Questions
Thanks Rainer, you've given me a few things to check first. I suspected motor and have tried 2 without change.by Klinger - Logo XXtreme 700/800 Questions
Hi, just wanting to check for problems changing Vbar on my 800. Couple of months ago the original YGE speedie blew up on the bench after 4 years of flying perfectly. Put in a Scorp Tribunis and ever since I'm getting both cyclic & tail kicks under load, never on bench. Log file has a lot of Sensor Data checksum errors and occasional Sensor Connection broken error. I originally didn't sby Klinger - Logo XXtreme 700/800 Questions
Hi, I've searched everywhere and cannot find much information on this. Wanting to run Vbar Gov, have setup ESC for fixed wing mode, have setup Vbar for gov and ESC signal from Servo port & ESC RPM signal wire into Sensor 2 port. Heli has separate Rx pack...no bec. Heli spools up to low headpseed & tries to govern, Vbar software shows the RPM signal but seems erratic and signal tooby Klinger - Questions V5
Hi, I've searched everywhere and cannot find much information on this. Wanting to run Vbar Gov, have setup ESC for fixed wing mode, have setup Vbar for gov and ESC signal from Servo port & ESC RPM signal wire into Sensor 2 port. Heli has separate Rx pack...no bec. Heli spools up to low headpseed & tries to govern, Vbar software shows the RPM signal but seems erratic and signal tooby Klinger - Setups
Many thanks Rainer for your reply. I've never seen that problem in 10 years in the hobby so you keep learning something new. Looking at pinions I can go to 19T to give me 2050 on the head but it looks like the only way to get 2150 is changing motor or speedie...by Klinger - Logo XXtreme 700/800 Questions
I've just rebuilt my 700 & had to put in a Extreme YGE 160HV speedie to replace a blown konny. The numbers say I should be able to govern at 2200 & my old setup with konny was governed 2150 but now with the YGE I cant get higher than around 1900. I've done the throttle setting procedure in vbar gov setup but 1900 is it. Even hooked it up to external rx and no difference. I don't kby Klinger - Logo XXtreme 700/800 Questions
Yes, i forgot to mention that, it does say "no license, demo mode". Why wouldnt the license work, is this the license for the phone app, when i uninstalled it and went to re-install it the android market said i'd already purchased it?by Klinger - Questions V5
Using the android app V1.2.1 on my HTC, my vibration analysis just stopped working. I saw a friends last weekend play up displaying the vibration level but with nothing in the frequency area. Mine has always worked in the past but just out of the blue lost all vibration analysis data and also cant recall any log data. I've tried clearing the cache as well as re-installing the app from scratchby Klinger - Questions V5
No bug, was just running the older version 1.0, after upgrading to V1.1.2 is working fineby Klinger - Questions V5
Maybe a bug in new android software...maybe me the active bank and view bank dosent display the correct bank selected although the parameters do change for the bank selected. When modifiying a selected bank setting, i change the number and wait for the "send" message to dissapear then if i change away from that bank and back to it the value hasnt been updated! On the banks screby Klinger - Questions V5
Just wondering if the android software will support version 2.2.1 on my HTC phone and when it might be ready? thanksby Klinger - Questions V5
Thanks Rainer, it is a V4 but i couldnt attach a vbr file so just renamed it xml. Tail servo was a BLS451 on a Fasst 8ch Rx with a 9Cap Tx. This glitch happens on the bench without motor running and even if i power from a seperate Rx battery instead of the BEC. After swapping only the V-bar from my other Logo the problem has followed the v-bar. Now in my other logo14 it does the same thing, oby Klinger - Questions V4
After a small meeting with the ground, i've rebilt my V4 Logo600 and noticed whilst on the bench the tail servo will give sudden kicks with no input from Tx or Gyro. Replaced Rx, Servo, tried powering from a battery, eventually pulled my newer plastic sensor V-stabi out of other machine and installed, updated to V4 and rel-loaded settings to find it fixed. then i re-installed the older silver sby Klinger - Questions V4