vbar neo blinking red

Hi. I have a vbar neo non vlink with a futaba sbus receiver and when i turn on the neo just start to blink red and the swash setup like 10 times or more.
Here is the log.
Regards

Sun Dec 22 20:23:21 ART 2019
Serial: 20006308
Firmware: 6.3
Patchlevel: 249
---- start ----

Warn 0:00 Init Failed, retrying...
Warn 0:01 Init Failed, retrying...
Warn 0:02 Init Failed, retrying...
Info 0:07 Calibration Finished
Warn 0:07 Ambiguous Value on Elevator RC Channel at Init

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...
Warn 0:04 Init Failed, retrying...

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...
Warn 0:04 Init Failed, retrying...

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
Warn 0:05 Ambiguous Value on Elevator RC Channel at Init

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...
OK 0:12 Good Health Message (10sec)
OK 0:22 Good Health Message (10sec)
OK 0:32 Good Health Message (10sec)
OK 0:42 Good Health Message (10sec)
OK 0:52 Good Health Message (10sec)
OK 1:02 Good Health Message (10sec)
OK 1:12 Good Health Message (10sec)
OK 1:22 Good Health Message (10sec)
OK 1:32 Good Health Message (10sec)
OK 1:42 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...
Info 0:08 Calibration Finished
Warn 0:08 Ambiguous Value on Elevator RC Channel at Init

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Critical 0:00 Aileron Sensor Value out of Range

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
Warn 0:05 Ambiguous Value on Elevator RC Channel at Init
OK 0:15 Good Health Message (10sec)
Info 0:20 Motor Switch operated to Idle bailout
Info 0:20 Motor Switch operated to ON
OK 0:30 Good Health Message (10sec)
OK 0:40 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
Info 0:24 Calibration Finished
Warn 0:24 Ambiguous Value on Elevator RC Channel at Init
OK 0:34 Good Health Message (10sec)
---- end ----

Quote:

Warn 0:24 Ambiguous Value on Elevator RC Channel at Init

Please check this TX channel calibration with the PC Software and also RX Failsafe settings (just hold except throttle).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.



1 mal bearbeitet. Zuletzt am 23.12.2019 06:24 von RV.