Setting up switch

I am tring to setup switch 6 to use with my switch glo ..just need to know how to make sw6 as a on off switch..please help bud

Well - which VBar is it?

Thinking about a NEO - use the 3-Level Macrocell:

https://www.vstabi.info/en/node/2211
https://uroehr.de/vtube/cat/macrocells-basics/video/04-three-level
https://www.vstabi.info/en/node/1912
https://www.vstabi.info/en/node/1925

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

Vbar touch and neo

Followed your video and all is working.thanks so much for your help..bud

Well done!

Pro Tip:

On my nitro i use the same switch as for "kill" - one end is glow, center is nothing and the other (could be momentary) is kill.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.

Thanks so much for the pro tip and help..bud

New to Vbar I'm installing a Neo into a Scale helicopter with retracts. How do I assign 3 servos to a channel and slow the signal down so the landing gear deploys slowly?

Thanks
Charles

From Alberta Canada

Hi Charles,

bascially, you connect the three servos to three physical outputs on your VBar NEO (might require a second one, an Extender).
There, you make the three physical outputs channels, and adjust directions, center positions and overall travel.
Input would be an unused macrocell, e.g. cell 27.
Make cell 27 a channel again, and again select an unused macrocell, e.g. cell 28, as the input.
In 27, you _only_ adjust the delay, and the fail safe position if you want.
Now make 28 3-Level, assign your preferred switch as an input (e.g. bank switch), and adjust the values for the three states of the switch, e.g. deployed-retracted-retracted.

Kind regards

Eddi

Born to fly ...
forced to work.

Well ... i made a video:

https://www.vstabi.info/en/node/2211

is the introduction to macrocells and ...

https://uroehr.de/vtube/cat/macrocells-basics

shows all cells

https://uroehr.de/vtube/cat/macrocells-basics/video/07-door-sequencer-with-macrocells?catName=macrocells-basics

Is "THE" overkill for gears ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.