I was flying my Synergy 556 today, and at the end of an auto right when I flared I lost all control and it crashed. I was less than a meter from the ground when it happened, so it was pretty much instant. It killed the engine, and right after it hit I heard the Vcontrol reconnect. Here is the log:
VBar Start -- Synergy 556 -- 09.09.2018 -- 16:21:12
16:21:12;1;Reset Reason: Power On
16:21:13;2;Bank 1 Loaded
16:21:14;2;Bank 4 Loaded
16:21:14;1;Motorswitch Motor Off
16:21:14;1;Motorswitch Idle Bailout
16:21:18;2;Calibration Finished
16:24:28;3;The Cyclic Ring is active
16:24:28;3;The Cyclic Ring is active
16:24:29;3;The Cyclic Ring is active
16:24:29;3;The Cyclic Ring is active
16:24:30;3;The Cyclic Ring is active
16:24:31;3;The Cyclic Ring is active
16:24:31;3;The Cyclic Ring is active
16:24:32;3;The Cyclic Ring is active
16:24:47;2;Governor Active
16:24:47;1;Motorswitch Motor On
16:25:01;3;High Vibration Level
16:25:08;2;Bank 2 Loaded
16:26:13;2;Bank 1 Loaded
16:29:35;2;Raised Vibration Level
16:31:17;2;Bank 4 Loaded
16:31:17;2;Governor Idle
16:31:17;1;Motorswitch Idle Bailout
16:31:21;2;Governor Stop
16:31:21;1;Motorswitch Motor Off
16:31:25;1;Motorswitch Idle Bailout
16:31:26;2;Bank 1 Loaded
16:31:26;2;Governor Active
16:31:26;1;Motorswitch Motor On
16:31:26;3;High Vibration Level
16:31:36;2;Raised Vibration Level
16:31:46;2;Raised Vibration Level
16:31:49;2;Governor Idle
16:31:49;1;Motorswitch Idle Bailout
16:31:49;2;Bank 4 Loaded
16:31:57;3;Reset Reason: Watchdog
16:31:57;2;Bank 1 Loaded
16:31:57;2;Bank 4 Loaded
16:31:57;4;Aileron Sensor Value out of Range
16:31:58;1;Motorswitch Motor Off
16:31:58;1;Motorswitch Idle Bailout
16:31:58;3;Init Failed, retrying...
16:32:01;1;Motorswitch Motor Off
16:32:01;2;Bank 1 Loaded
16:32:02;2;Calibration Finished
16:32:22;2;Raised Vibration Level
16:32:46;3;RC Voltage: 6.82V
16:34:23;3;RC Voltage: 6.82V
VBar Logfile End -- 09.09.2018 -- 16:34:25
I'm guessing it's right there at Reset Reason: Watchdog. This is a Neo that I purchased new in July and upgraded to Pro Rescue. This is a heli that I use to train my son with using a single Spektrum satellite and crossover buddy boxing. At the end of July the heli did the same thing in my N5C. I blamed it on my own thumbs and didn't check the log, and unfortunately I don't have that log anymore.
So does anyone have any ideas? I have 8 Vlink Neos in use, and this is the only one where I am using a Spektrum satellite for crossover buddy boxing. It has probably 100 flights out of the 500 or so that I've put on all of my Neos with my Vcontrol, and it is the only one that has had any issues, and the 2 times it was during a flight where I was training my son.
I won't be doing the crossover buddy boxing much longer, at some point my Vcontrol Touch will ship. I'd like to know that this Neo is safe to keep using though.