I am getting the "Error;Extreme Vibration Level" in the logs pretty much the entire flight. This is a 8S Tron Dnamic helicopter flown mostly at 1600rpm. I originally built this helicopter with a Spirit GTR unit, and it was flying fine. I replaced the Spirit GTR with a V2 EVO unit which is showing these "Error;Extreme Vibration Level" messages in the logs. I checked the main shaft, spindle shaft, and tail shaft with a 0.0005in dial indicator, and the indicator needle did not move at all when I spun the shafts. I tested all the bearings before assembling the helicopter. The helicopter now has 45 flights, so I would think all the parts have worn in by now. The major issue I encountered is that despite having a level swash at mid/high/low collective stick and attaining an optimal fore/aft center of gravity by shifting the 8S 4000mah battery pretty forward, the helicopter starts to lean back on the ground while spooling; the tail fin will drop until it contacts the ground. It leans back when I hover upright, but it leans forward when I hover inverted. I conducted an "AutoTrim", and it ended with an elevator trim of "+102". Thinking that this could be a faulty EVO unit, replaced the EVO with another EVO unit, and the weird elevator issue needing trimming persisted. With this "+102" elevator trim, the helicopter is flying really well fairly well. It no longer leans back during spoolup either. The only issue I notice is that the helicopter begins to lean back during flight if I "bang" the collective stick up and down several times. I am posting this issue here because I have never experienced this elevator behavior in other helicopters before and I am getting the "Error;Extreme Vibration Level" message in the logs. I am wondering how to approach this. Full flight log: 11.07.2024 18:34:30;VBar Start -- Tron Dnamic2 -- 0027002130 -- V 7.1 -- pl 155 11.07.2024 18:34:30 Good;Coldstart 11.07.2024 18:34:30 Good;Reset Reason: Power On 11.07.2024 18:34:31 Info;Bank 1 Loaded 11.07.2024 18:34:31 Info;Bank 2 Loaded 11.07.2024 18:34:35 Good;YGE ESC detected 11.07.2024 18:34:36 Info;Calibration Finished 11.07.2024 18:34:39 Good;Top 5 Selection: 8S B 4000mah ManiaX 11.07.2024 18:36:06 Info;Bank 1 Loaded 11.07.2024 18:36:07 Good;Motorswitch Idle Bailout 11.07.2024 18:36:07 Good;Motorswitch Motor On 11.07.2024 18:36:21 Info;Bank 2 Loaded 11.07.2024 18:36:27 Error;Extreme Vibration Level 11.07.2024 18:36:37 Error;Extreme Vibration Level 11.07.2024 18:36:47 Error;Extreme Vibration Level 11.07.2024 18:36:58 Error;Extreme Vibration Level 11.07.2024 18:37:07 Error;Extreme Vibration Level 11.07.2024 18:37:17 Error;Extreme Vibration Level 11.07.2024 18:37:28 Error;Extreme Vibration Level 11.07.2024 18:37:38 Error;Extreme Vibration Level 11.07.2024 18:37:48 Error;Extreme Vibration Level 11.07.2024 18:37:58 Error;Extreme Vibration Level 11.07.2024 18:38:08 Error;Extreme Vibration Level 11.07.2024 18:38:18 Error;Extreme Vibration Level 11.07.2024 18:38:28 Error;Extreme Vibration Level 11.07.2024 18:38:38 Error;Extreme Vibration Level 11.07.2024 18:38:48 Error;Extreme Vibration Level 11.07.2024 18:38:50 Info;Bank 1 Loaded 11.07.2024 18:38:55 Info;Bank 2 Loaded 11.07.2024 18:38:59 Error;Extreme Vibration Level 11.07.2024 18:38:59 Info;Bank 3 Loaded 11.07.2024 18:39:09 Error;Extreme Vibration Level 11.07.2024 18:39:19 Error;Extreme Vibration Level 11.07.2024 18:39:29 Error;Extreme Vibration Level 11.07.2024 18:39:39 Error;Extreme Vibration Level 11.07.2024 18:39:49 Error;Extreme Vibration Level 11.07.2024 18:39:59 Error;Extreme Vibration Level 11.07.2024 18:40:10 Error;Extreme Vibration Level 11.07.2024 18:40:20 Error;Extreme Vibration Level 11.07.2024 18:40:30 Error;Extreme Vibration Level 11.07.2024 18:40:40 Error;Extreme Vibration Level 11.07.2024 18:40:47 Good;Motorswitch Idle Bailout 11.07.2024 18:40:50 Error;Extreme Vibration Level 11.07.2024 18:41:00 Error;Extreme Vibration Level 11.07.2024 18:41:03 Warn;YGE Overcurrent 11.07.2024 18:41:03 Good;Motorswitch Motor Off 11.07.2024 18:41:03 Info;Off - ESC - Umin:27.7V Imax:180.4A Temp:44° 11.07.2024 18:44:00 Good;YGE ESC Disconnected 11.07.2024 18:44:05;VBar Logfile End -- 11.07.2024 -- 18:44:04 https://www.vstabi.info/forum/read.php?64,203323,203323#msg-203323 Fri, 07 Aug 2026 17:50:30 +0200 Phorum 5.2.7 https://www.vstabi.info/forum/read.php?64,203323,203552#msg-203552 https://www.vstabi.info/forum/read.php?64,203323,203552#msg-203552 RV VBar VLink Mon, 05 Aug 2024 06:14:43 +0200 https://www.vstabi.info/forum/read.php?64,203323,203549#msg-203549 https://www.vstabi.info/forum/read.php?64,203323,203549#msg-203549
I replaced all 3 cyclic servos, and now the helicopter is performing really well as expected. It is performing so well, I forgot to check vibrations levels. :)-D]]> johnahamelv VBar VLink Mon, 05 Aug 2024 00:25:40 +0200 https://www.vstabi.info/forum/read.php?64,203323,203355#msg-203355 https://www.vstabi.info/forum/read.php?64,203323,203355#msg-203355
by comparison, what did the logs from the Spirit GTR show?

If you get such a high auto trim value, this could either be because the VBar properly senses that this trim is required, or because the vibration levels even in a hover are adverse enough to interfere even with the gyros.
The cross check with a different VBar EVO pretty much takes those out of the equation.
To check for vibration issues during the trim flight, cancel the +102 and trim accordingly, manually, in setup (approx. same swash plate deflection), then trim-fly again. If this value was considerably lower now (which I'd expect), it's pretty much proof that this trim is indeed necessary.
Maybe it trims even more now, and maybe the leaning-back issue also becomes less ...

If the tail drops, the heli leans backwards, with a couple of collective pitch pumps, it's normally evidence for either an off center of gravity, or an off elevator pre-compensation value, or maybe even for a bad servo (suspect, the single servo).

In addition to the screenshots Rainer asked for, I'd also be curious to see a couple of clear, informative photos from the model, showing the servo/swash plate/main rotor layout, and the layout of the electronics. Clear, informative, compared to artistic ;)

Kind regards

Eddi]]> Eddi E. aus G. VBar VLink Mon, 15 Jul 2024 11:08:53 +0200 https://www.vstabi.info/forum/read.php?64,203323,203324#msg-203324 https://www.vstabi.info/forum/read.php?64,203323,203324#msg-203324
Is there some screenshots available of the vibration analysis in a hover?

As best with the pro value pack on the elevator sensor in this case.]]> RV VBar VLink Sat, 13 Jul 2024 09:41:51 +0200 https://www.vstabi.info/forum/read.php?64,203323,203323#msg-203323 https://www.vstabi.info/forum/read.php?64,203323,203323#msg-203323
With this "+102" elevator trim, the helicopter is flying really well fairly well. It no longer leans back during spoolup either. The only issue I notice is that the helicopter begins to lean back during flight if I "bang" the collective stick up and down several times.

I am posting this issue here because I have never experienced this elevator behavior in other helicopters before and I am getting the "Error;Extreme Vibration Level" message in the logs. I am wondering how to approach this.

Full flight log:
11.07.2024 18:34:30;VBar Start -- Tron Dnamic2 -- 0027002130 -- V 7.1 -- pl 155
11.07.2024 18:34:30 Good;Coldstart
11.07.2024 18:34:30 Good;Reset Reason: Power On
11.07.2024 18:34:31 Info;Bank 1 Loaded
11.07.2024 18:34:31 Info;Bank 2 Loaded
11.07.2024 18:34:35 Good;YGE ESC detected
11.07.2024 18:34:36 Info;Calibration Finished
11.07.2024 18:34:39 Good;Top 5 Selection: 8S B 4000mah ManiaX
11.07.2024 18:36:06 Info;Bank 1 Loaded
11.07.2024 18:36:07 Good;Motorswitch Idle Bailout
11.07.2024 18:36:07 Good;Motorswitch Motor On
11.07.2024 18:36:21 Info;Bank 2 Loaded
11.07.2024 18:36:27 Error;Extreme Vibration Level
11.07.2024 18:36:37 Error;Extreme Vibration Level
11.07.2024 18:36:47 Error;Extreme Vibration Level
11.07.2024 18:36:58 Error;Extreme Vibration Level
11.07.2024 18:37:07 Error;Extreme Vibration Level
11.07.2024 18:37:17 Error;Extreme Vibration Level
11.07.2024 18:37:28 Error;Extreme Vibration Level
11.07.2024 18:37:38 Error;Extreme Vibration Level
11.07.2024 18:37:48 Error;Extreme Vibration Level
11.07.2024 18:37:58 Error;Extreme Vibration Level
11.07.2024 18:38:08 Error;Extreme Vibration Level
11.07.2024 18:38:18 Error;Extreme Vibration Level
11.07.2024 18:38:28 Error;Extreme Vibration Level
11.07.2024 18:38:38 Error;Extreme Vibration Level
11.07.2024 18:38:48 Error;Extreme Vibration Level
11.07.2024 18:38:50 Info;Bank 1 Loaded
11.07.2024 18:38:55 Info;Bank 2 Loaded
11.07.2024 18:38:59 Error;Extreme Vibration Level
11.07.2024 18:38:59 Info;Bank 3 Loaded
11.07.2024 18:39:09 Error;Extreme Vibration Level
11.07.2024 18:39:19 Error;Extreme Vibration Level
11.07.2024 18:39:29 Error;Extreme Vibration Level
11.07.2024 18:39:39 Error;Extreme Vibration Level
11.07.2024 18:39:49 Error;Extreme Vibration Level
11.07.2024 18:39:59 Error;Extreme Vibration Level
11.07.2024 18:40:10 Error;Extreme Vibration Level
11.07.2024 18:40:20 Error;Extreme Vibration Level
11.07.2024 18:40:30 Error;Extreme Vibration Level
11.07.2024 18:40:40 Error;Extreme Vibration Level
11.07.2024 18:40:47 Good;Motorswitch Idle Bailout
11.07.2024 18:40:50 Error;Extreme Vibration Level
11.07.2024 18:41:00 Error;Extreme Vibration Level
11.07.2024 18:41:03 Warn;YGE Overcurrent
11.07.2024 18:41:03 Good;Motorswitch Motor Off
11.07.2024 18:41:03 Info;Off - ESC - Umin:27.7V Imax:180.4A Temp:44°
11.07.2024 18:44:00 Good;YGE ESC Disconnected
11.07.2024 18:44:05;VBar Logfile End -- 11.07.2024 -- 18:44:04]]> johnahamelv VBar VLink Fri, 12 Jul 2024 23:08:47 +0200